you have a PM 
z28 roller
Thread Starter
Teching In
Joined: Nov 2004
Posts: 1
Likes: 0
z28 roller BMR K member with lower and upper A arms
BMR Subframe connectors
BMR Driveshaft loop
BMR Panhard Rod
Wolfe Rear control arms
Wolfe Sway bar
Wolfe Torque arm
Wolfe 6pt cage with swing outs Also have the front half to convert the cage to a 10pt
Battery box relocated to the rear with kill switch
Moser 9in with 3.55's spool and 33 spline axles
Speed Inc fuel tank
Sparco stering wheel
Harwood ss pin-on hood.
Qa1 R coil overs in front
Qa1 R adjustable rear shocks
Strange front and rear drag brakes
Bogart D10's
Hoosier front runners and 28.10 rear slicks
Billingsley manual master with line lock
TSP smoked lid
Over flow bottle
B&M ratchit shifter
All the wolfe stuff is chromoly. The brake lines need to be hooked up to the master. The master also needs to be hooked to the brake peddle. The body is in nice shap the paint is a little ruff but not to bad. I do not have a seat for the car i was going to put one race seat in it. All the work as done by CJ at RMP in lewisville. The car has been gutted. With motor and tranny the car should weight in around 2900 or so. I can e-mail pics so pm me your e-mai address.
http://www.dfwstangs.net/forums/showthread.php?t=206217 pics
6500
BMR Subframe connectors
BMR Driveshaft loop
BMR Panhard Rod
Wolfe Rear control arms
Wolfe Sway bar
Wolfe Torque arm
Wolfe 6pt cage with swing outs Also have the front half to convert the cage to a 10pt
Battery box relocated to the rear with kill switch
Moser 9in with 3.55's spool and 33 spline axles
Speed Inc fuel tank
Sparco stering wheel
Harwood ss pin-on hood.
Qa1 R coil overs in front
Qa1 R adjustable rear shocks
Strange front and rear drag brakes
Bogart D10's
Hoosier front runners and 28.10 rear slicks
Billingsley manual master with line lock
TSP smoked lid
Over flow bottle
B&M ratchit shifter
All the wolfe stuff is chromoly. The brake lines need to be hooked up to the master. The master also needs to be hooked to the brake peddle. The body is in nice shap the paint is a little ruff but not to bad. I do not have a seat for the car i was going to put one race seat in it. All the work as done by CJ at RMP in lewisville. The car has been gutted. With motor and tranny the car should weight in around 2900 or so. I can e-mail pics so pm me your e-mai address.
http://www.dfwstangs.net/forums/showthread.php?t=206217 pics
6500
Trending Topics
TECH Addict
Joined: Nov 2001
Posts: 2,021
Likes: 0
From: Angleton/Lake Jackson (South of Houston)
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Thread Starter
Teching In
Joined: Nov 2004
Posts: 1
Likes: 0
Originally Posted by distortion_69
Did you get my pm? I was going to strip my car up to turbo it, but I'd much rather trade it and leave it as is and use an already completed rolling chassis.
Thanks,
Josh
Thanks,
Josh
Pm sent
