FS: LS1 Block & Internals

Reply Subscribe

Thread Tools

Search this Thread

Dec 18, 2008 | 08:42 AM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

FS: LS1 Block & Internals

I am parting my short block, has a crack in cylinder #2, the block can be fixed and its only about $100 total to do so but here are the parts:

Short block as a whole: $150.00

parted

Block $75 (Fix it or make a table)
Crank $75
Pistons w/ Rods $75
Lifters $15
98 Cam $15
Timing Set $15
Front Cover $30
Rear Cover $30
Valley Cover $15
Oil Pump $15
Pushrods $10

All parts have about 100k but are in great shape.

*NOTE: This short block doesnt come as pictured, it comes without the Oil Pan or sensors and without the starter shield. I will throw in the pushrods for free as I do not need them.*

Last edited by Mike96z; Dec 19, 2008 at 07:33 PM.

Dec 18, 2008 | 09:08 AM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

All prices obo.

Dec 18, 2008 | 09:41 AM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

Short block is still assembled.

Dec 18, 2008 | 01:34 PM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

Dec 18, 2008 | 01:35 PM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

Engine idled and ran fine, did pass a compression test, although it did misfire or backfire but it also had a bad set of heads on it so not sure what the issue is, I just seen the crack in #2 when pulling it but im not sure that was the problem but it couldve been in development.

Dec 18, 2008 | 02:15 PM

connexion2005

12 Second Club

iTrader: (49)

Joined: May 2006

Posts: 966

Likes: 0

From: College Station, Texas

Can I get a close up of that cylinder? A picture I mean.

Dec 18, 2008 | 02:53 PM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

No prob, will get the picture for you tonight. I meant to do that but I didnt have time.

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Dec 19, 2008 | 01:21 AM

Mike96z

Thread Starter

TECH Fanatic

iTrader: (78)

Joined: Feb 2007

Posts: 1,075

Likes: 0

From: Dallas, TX

Here are the pics of the cracked cylinder. The first pic I outlined it in red so you can see it then you could notice it in the others, its kinda curved.