FS: 95 Firehawk
#1
Thread Starter
TECH Enthusiast
iTrader: (47)
Joined: Feb 2005
Posts: 518
Likes: 0
From: San Diego, CA
FS: 95 Firehawk $2500
deal pending
Car is a '95 A4, Black, T-tops with Trans Am hatch. 100K miles, stock factory suspension
Factory SLP options: Ram air, 5 spoke Speedline wheels with 275-40-17 tires, 3 in. exhaust with 2OTL muffler, 3.23 gears, transmission performance switch on center console (makes it shift harder)
Car went 13.5@101 with the drag radials and made 270hp/290tq before any mods
Mods are:
Pacesetter long tubes and ORY (no emissions) and a bullet muffler in the I-pipe so it's not too loud
Prothane motor mounts
MSD 6A box and coil
2500 stall Hughes converter and trans cooler
LT4 timing set
LT4 valvesprings
ARP head bolts
LT4 knock module
PCM4less tune
Manual fan switch
28lb LT4 fuel injectors
New parts:
Alternator
Waterpump
Power steering pump
Starter
FP regulator
EGR valve
All sensors; TPS, MAF, MAP, ECT, KS, IAT
The heads had a valve job last September along with being milled and the LT4 springs installed.
The bad:
Car has been sitting since October because a lifter chewed up a cam lobe. The cam is out, the front and top are tore down but the heads are still on. It has been outside but I have the interior protected with a cover. The drivers side seat has the usual wear but no cracks in the dash. The paint is decent but the front are rear bumpers are a little faded. T-tops are tinted.
The parts alone are worth more than I'm asking.
$3,500
Car is a '95 A4, Black, T-tops with Trans Am hatch. 100K miles, stock factory suspension
Factory SLP options: Ram air, 5 spoke Speedline wheels with 275-40-17 tires, 3 in. exhaust with 2OTL muffler, 3.23 gears, transmission performance switch on center console (makes it shift harder)
Car went 13.5@101 with the drag radials and made 270hp/290tq before any mods
Mods are:
Pacesetter long tubes and ORY (no emissions) and a bullet muffler in the I-pipe so it's not too loud
Prothane motor mounts
MSD 6A box and coil
2500 stall Hughes converter and trans cooler
LT4 timing set
LT4 valvesprings
ARP head bolts
LT4 knock module
PCM4less tune
Manual fan switch
28lb LT4 fuel injectors
New parts:
Alternator
Waterpump
Power steering pump
Starter
FP regulator
EGR valve
All sensors; TPS, MAF, MAP, ECT, KS, IAT
The heads had a valve job last September along with being milled and the LT4 springs installed.
The bad:
Car has been sitting since October because a lifter chewed up a cam lobe. The cam is out, the front and top are tore down but the heads are still on. It has been outside but I have the interior protected with a cover. The drivers side seat has the usual wear but no cracks in the dash. The paint is decent but the front are rear bumpers are a little faded. T-tops are tinted.
The parts alone are worth more than I'm asking.
$3,500
Last edited by 1badchicken; 01-07-2009 at 10:14 PM.
#5
Thread Starter
TECH Enthusiast
iTrader: (47)
Joined: Feb 2005
Posts: 518
Likes: 0
From: San Diego, CA
sure will. I just need the cash. I bought a Ls1 T/A this weekend and I have to put the cash in my bank before my wife finds out!!!! LOL
It's a clean Firehawk for the money....
So If any one has a LS1 WS6 hood in silver or some wheels+ cash LMK.
It's a clean Firehawk for the money....
So If any one has a LS1 WS6 hood in silver or some wheels+ cash LMK.
#6
Trending Topics
#10
Thread Starter
TECH Enthusiast
iTrader: (47)
Joined: Feb 2005
Posts: 518
Likes: 0
From: San Diego, CA
The engne is pulled so there is nothing to really see. I can get you the build codes but it is a true firehawk. Its too dark to take pics i'll post some tomorrow. The dash is crack free. The only interior issue is the driver seat. Its has a couple of tears which is typical. But for $3500 with the mods, that is a steal
#11
If you still have this as the end of January there's a pretty good chance it'll come home with me. I'll keep my eye out to see if it sells or not.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.
#12
Thread Starter
TECH Enthusiast
iTrader: (47)
Joined: Feb 2005
Posts: 518
Likes: 0
From: San Diego, CA
If you still have this as the end of January there's a pretty good chance it'll come home with me. I'll keep my eye out to see if it sells or not.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.
yeah just keep an eye up. I just need it out of the driveway pretty soon.
#14
Thread Starter
TECH Enthusiast
iTrader: (47)
Joined: Feb 2005
Posts: 518
Likes: 0
From: San Diego, CA
If you still have this as the end of January there's a pretty good chance it'll come home with me. I'll keep my eye out to see if it sells or not.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.
You said it had a valve job does that mean just replaced the stock stuff or are the valves bigger now? Looks like a good deal for someone, hopefully me.