Clean Out-Trade
Clean Out-Trade Lakewood Bellhousing to put a T10,muncie,Saginaw Manual transmissions behind the lsx engines
350$
Crane Cams 1.8 Gold Roller Rockers Used for 5 Passes
http://cranecams.com/?show=browsePar...ber=144759A-16
300$
NEW Lsx Proble Stroker pistons NIB 19,3CC dish,locks included
LS1 - 3.900 Stroke - 6.125 Rod - 1.175 C/H - .927 x 2.500 - 118 Gram Pin New 300$
Used JE custom 427 Pistons for 6.125rods and 4"Crank SBC or LSx
4.120 Diameter,1.115 CH,440 grams
3914F forgings
927" x 2.500" with .150" straight wall for spiro locks (included)
8.4CC - 0.080 Dish
Cost new 950$ will let go for 350$ shipped
NIB MSD Dis 2 Digital box NIB 350$
NIb Eaton Detroit Locker AMC 20, NIB 400$
6-71 Detroit Blower,Sandblasted case and good screws 300$
Crower Enduro II 1.5 7/16 Roller Rockers used 1000miles 300$ (450$ new)
New LT1 Mcleod Billet Flywheel 250
NIB Accell 26# injectors
LS1 Injectors 40$
Mainfolds 40$
AFR 220 Spreadport SBC Heads Ported 1200$
TPI Intake setup for pre 86' SBC,comes with Fuel Rails and injectors 250$
Accell DFI 74001 400$
Willing to trade for:
Both 4wd and 2wd:4l80-Th400
Iron 6L-5.3 or AL 5.7 LS1 engines any condition
9" Ford: 35 Spline Spool and Aftermarket 3rd member
PM me
350$
Crane Cams 1.8 Gold Roller Rockers Used for 5 Passes
http://cranecams.com/?show=browsePar...ber=144759A-16
300$
NEW Lsx Proble Stroker pistons NIB 19,3CC dish,locks included
LS1 - 3.900 Stroke - 6.125 Rod - 1.175 C/H - .927 x 2.500 - 118 Gram Pin New 300$
Used JE custom 427 Pistons for 6.125rods and 4"Crank SBC or LSx
4.120 Diameter,1.115 CH,440 grams
3914F forgings
927" x 2.500" with .150" straight wall for spiro locks (included)
8.4CC - 0.080 Dish
Cost new 950$ will let go for 350$ shipped
NIB MSD Dis 2 Digital box NIB 350$
NIb Eaton Detroit Locker AMC 20, NIB 400$
6-71 Detroit Blower,Sandblasted case and good screws 300$
Crower Enduro II 1.5 7/16 Roller Rockers used 1000miles 300$ (450$ new)
New LT1 Mcleod Billet Flywheel 250
NIB Accell 26# injectors
LS1 Injectors 40$
Mainfolds 40$
AFR 220 Spreadport SBC Heads Ported 1200$
TPI Intake setup for pre 86' SBC,comes with Fuel Rails and injectors 250$
Accell DFI 74001 400$
Willing to trade for:
Both 4wd and 2wd:4l80-Th400
Iron 6L-5.3 or AL 5.7 LS1 engines any condition
9" Ford: 35 Spline Spool and Aftermarket 3rd member
PM me
Last edited by Ari G; Jun 16, 2009 at 05:34 PM.
