Irwindale this thursday...
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Got injectors, but have no one to tune car. George is extremely busy with personal matters and i don't trust any one else to touch my car. It could be up to a month before i see them in my car, so for now have to shift at 5800-5900 to be safe.
Gotcha, yeah I hope he gets things worked out, shenanigans I tell ya. Well I should be there too and I will run.
Thread Starter
10 Second Club
iTrader: (26)
Joined: Jul 2005
Posts: 3,725
Likes: 1
From: Spokane, Wa
Motor's still fresh so I'm not spraying it. It's gonna be undergeared with the 4.11s plus i only have a 1330 joint in the rear so I'm not sure about 6k rpm dumps. Don't have a 2 step on it yet, plus I've never driven on a bias ply tire before haha so if it runs 9.5 at 98 mph then we know where the problem is.
Motor's still fresh so I'm not spraying it. It's gonna be undergeared with the 4.11s plus i only have a 1330 joint in the rear so I'm not sure about 6k rpm dumps. Don't have a 2 step on it yet, plus I've never driven on a bias ply tire before haha so if it runs 9.5 at 98 mph then we know where the problem is.
Thread Starter
10 Second Club
iTrader: (26)
Joined: Jul 2005
Posts: 3,725
Likes: 1
From: Spokane, Wa
yea motor is new, went with the mcleod bellhousing, new spec stage 5, stock trans, pst shaft, 9" has only 1k miles in 2 years. I haven't taken this car to the track in almost 3 years, and that was when it was making maybe 400 rwhp with ported heads and a cc306. It'd be cool if a lot of guys went out to give me some input, especially what the car's doing at launch. I've got a decent idea of shock settings, but i don't have a DA shock in the rear which is going to give me some problems. Oh yea Spec said you dont' need to break in their stage 5 since its a track clutch, just make a few easy passes and it's good to go, but I've put about 75 street miles on the car already so it'll be fine.
Thread Starter
10 Second Club
iTrader: (26)
Joined: Jul 2005
Posts: 3,725
Likes: 1
From: Spokane, Wa
oh yea stock rear sway bar too 
i have a bmr anti roll bar, but need the brackets welded to the frame and then i need to order the mounting brackets that go on the axle tubes. I think I'm gonna be getting a lot of twist on the launch.
i have a bmr anti roll bar, but need the brackets welded to the frame and then i need to order the mounting brackets that go on the axle tubes. I think I'm gonna be getting a lot of twist on the launch.