then i gotta take a test and do 3 more and take another test 
the fun begins
Thread Starter
11 Second Club
iTrader: (9)
Joined: Mar 2007
Posts: 1,016
Likes: 0
From: Avondale, AZ
. I just wired up the bottle heater though cause i was bored and needed to entertain myself. Tues if i still dont have it i'm going to attempt plugs 
. I am not looking foward to that at all. Thread Starter
11 Second Club
iTrader: (9)
Joined: Mar 2007
Posts: 1,016
Likes: 0
From: Avondale, AZ
yea i have smaller arms. bought a flex head rachet from autozone yesterday and its got a bend towards the bottom of the handle looked like it might be helpfull. Have a couple diff length extentsions so hopefully wont be bad
how was the wiring of the heater? not too much of a pita?
Thread Starter
11 Second Club
iTrader: (9)
Joined: Mar 2007
Posts: 1,016
Likes: 0
From: Avondale, AZ
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
11 Second Club
iTrader: (9)
Joined: Mar 2007
Posts: 1,016
Likes: 0
From: Avondale, AZ
sounds fantabulous! hope ur mounting bracket and **** come in soon so you can finish!
Thread Starter
11 Second Club
iTrader: (9)
Joined: Mar 2007
Posts: 1,016
Likes: 0
From: Avondale, AZ
yea my hands look like i boxed a cat or something. All chewed up but 2 hours later i was done. Spent an hour almost trying to get the back bolt off the coil back rack, finally got that off and from there it was a breeze. Once you take that off getting number 8 from the engine bay is a snap. I found the best set up to be a spark plug socket, pivoting head rachet, 3" extension (not always used), and a socket that fits the end of the spark plug socket. Just break the plugs loose screw them out take the new plug and the socket only hand tighten it back in then put the socket that fits that end back over the spark plug socket and give it a 1/4 turn. Nice and simple. I only put the 2 bolts back in on the coil pack rack so now it should only take me 30-45 mins to swap out plugs at most
yea my hands look like i boxed a cat or something. All chewed up but 2 hours later i was done. Spent an hour almost trying to get the back bolt off the coil back rack, finally got that off and from there it was a breeze. Once you take that off getting number 8 from the engine bay is a snap. I found the best set up to be a spark plug socket, pivoting head rachet, 3" extension (not always used), and a socket that fits the end of the spark plug socket. Just break the plugs loose screw them out take the new plug and the socket only hand tighten it back in then put the socket that fits that end back over the spark plug socket and give it a 1/4 turn. Nice and simple. I only put the 2 bolts back in on the coil pack rack so now it should only take me 30-45 mins to swap out plugs at most
