Does a wiring guide exist...
Thread Starter
On The Tree
iTrader: (15)
Joined: Dec 2006
Posts: 166
Likes: 0
From: Manitoba, Canada
Does a wiring guide exist... Hooked up my panasonic head unit last night.
Now its time for the amps, subs and speakers.
Just wondering if there is a guide as to where to run the wires, etc to make it simpler...
I will run a power wire from the battery to the back, and rca and amp power wires on the driver side. Do you run the front speaker wires on the driver side as well? (To one of the amps i am adding)
Guess my biggest worry is how to get from the battery into the car, hopefully there is a spot there i can use.
Now its time for the amps, subs and speakers.
Just wondering if there is a guide as to where to run the wires, etc to make it simpler...
I will run a power wire from the battery to the back, and rca and amp power wires on the driver side. Do you run the front speaker wires on the driver side as well? (To one of the amps i am adding)
Guess my biggest worry is how to get from the battery into the car, hopefully there is a spot there i can use.
Looks good. I'm guessing that black thing out of the amp is the ground? That's the only one I don't see labeled. Make sure you ground the amp well 
And use wire as thick, or thicker, than your power wire.
I'm pretty sure speaker wire can be ran by power wire as well. I can't remember for sure on that one.
And use wire as thick, or thicker, than your power wire.I'm pretty sure speaker wire can be ran by power wire as well. I can't remember for sure on that one.
Thread Starter
On The Tree
iTrader: (15)
Joined: Dec 2006
Posts: 166
Likes: 0
From: Manitoba, Canada
I stole that picture from the net...
Oops..i think the amp power wire needs to run with the main power wire..not the speaker/rca wires. (the diagram had it right, my wording in the first post was wrong).
I have:
JBL 608 GTI components for the front
JBL P652s for the rears
Infinity 12DVQ subs (2 of them in a subthump box)
Infinity 1211a 1200 watt sub amp
Infinity 7541 520 watt amp
2 capicitors...and all the wiring goodies...
I think it will sound pretty good.
Oops..i think the amp power wire needs to run with the main power wire..not the speaker/rca wires. (the diagram had it right, my wording in the first post was wrong).
I have:
JBL 608 GTI components for the front
JBL P652s for the rears
Infinity 12DVQ subs (2 of them in a subthump box)
Infinity 1211a 1200 watt sub amp
Infinity 7541 520 watt amp
2 capicitors...and all the wiring goodies...
I think it will sound pretty good.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
2 7mm bolts holding on the wiring harnesses and 2 10mm bolts holding in the pcm itself..
be sure to disconnect the battery before you do this...
you will need to make a slight slit in the grommet in order to rout your wire through there.. i found it easier to go from inside the car into the engine bay...
there is a black panel under the glove box held in by a couple push pins that you will need to remove in order to access the grommet from the inside (you might have to remove the kick panel aswell.. mine was already out)
be sure to disconnect the battery before you do this...
you will need to make a slight slit in the grommet in order to rout your wire through there.. i found it easier to go from inside the car into the engine bay...
there is a black panel under the glove box held in by a couple push pins that you will need to remove in order to access the grommet from the inside (you might have to remove the kick panel aswell.. mine was already out)
