LS1TECH - Camaro and Firebird Forum Discussion
Opposite view
Opposite view
0 2011/06/10 14:52:27
Bottle view
Bottle view
0 2011/06/10 14:52:27
Bottle in hatch area.
Bottle in hatch area.
0 2011/06/10 14:50:32
12 volt source to switch panel
12 volt source to switch panel
0 2011/06/10 14:50:32
switch panel
switch panel
0 2011/06/10 14:50:32
SS1875
SS1875
0 2011/05/26 16:40:16
PCM removed and wires being run through the firewall to the switch plate.
PCM removed and wires being run through the firewall to the switch plate.
0 2011/05/26 16:38:05
Deciding how to run the wires for the DDWS
Deciding how to run the wires for the DDWS
0 2011/05/26 16:38:05
90mm Plate, solenoids, purge,lines and brackets in place.
90mm Plate, solenoids, purge,lines and brackets in place.
0 2011/05/26 16:38:05
Power wire from bottle relay along with the Nitrous main feed line. Pre-switch panel wiring.
Power wire from bottle relay along with the Nitrous main feed line. Pre-switch panel wiring.
0 2011/05/26 16:37:26
Wiring up the switch panel and 12 volt source to the fuse panel via a tap-a-circuit (used the gauges fuse)
Wiring up the switch panel and 12 volt source to the fuse panel via a tap-a-circuit (used the gauges fuse)
0 2011/05/26 16:37:26
Closer view of the wiring fun!
Closer view of the wiring fun!
0 2011/05/26 16:37:26
00 Camaro PCM RPM White wire-pin #10 under red connector TPS Dark Blue wire-pin#24 also under red connector. For connection to the DDWS from Nitro Dave's
00 Camaro PCM RPM White wire-pin #10 under red connector TPS Dark Blue wire-pin#24 also under red connector. For connection to the DDWS from Nitro Dave's
0 2011/05/26 16:36:40
Mounted the relay on the PCM bracket. Getting wires sorted for connection to solenoids and fpss and ddws.
Mounted the relay on the PCM bracket. Getting wires sorted for connection to solenoids and fpss and ddws.
0 2011/05/26 16:36:40
Better picture of the relay mounted.
Better picture of the relay mounted.
0 2011/05/26 16:36:40
Mostly done with wiring at this point.
Mostly done with wiring at this point.
0 2011/05/26 16:35:38
Not bad for my first install.
Not bad for my first install.
0 2011/05/26 16:35:38
Closeup of the purge line and the solenoid brackets from Nitro Dave's.
Closeup of the purge line and the solenoid brackets from Nitro Dave's.
0 2011/05/26 16:35:38
Nitro Dave's DDWS mounted and wired up.
Nitro Dave's DDWS mounted and wired up.
0 2011/05/26 16:34:31
Switch plate wiring done, OTHER than the 12 volt keyed source wire which is seen lying on the floor mat.
Switch plate wiring done, OTHER than the 12 volt keyed source wire which is seen lying on the floor mat.
0 2011/05/26 16:34:31
Wiring all loomed up.
Wiring all loomed up.
0 2011/05/26 16:34:31
Solenoids and brackets.
Solenoids and brackets.
0 2011/05/26 16:33:07
Used factory loom to hide the ground wires for the solenoids. Bolt on the front of the passenger side head used for ground.
Used factory loom to hide the ground wires for the solenoids. Bolt on the front of the passenger side head used for ground.
0 2011/05/26 16:33:07