LS1TECH - Camaro and Firebird Forum Discussion
Finally done porting lower shell and using spare motor to mock up custom valley cover bolts and mod original LS1 coolant tubes so all points of the heads get coolant
Finally done porting lower shell and using spare motor to mock up custom valley cover bolts and mod original LS1 coolant tubes so all points of the heads get coolant
0 2012/03/07 19:58:16
20 hours of handporting, not even counting epoxy work to fix what the very first owner did by not reading instructions about replacing valley cover bolts. Had to fix 6 cracks. Hope it holds together
20 hours of handporting, not even counting epoxy work to fix what the very first owner did by not reading instructions about replacing valley cover bolts. Had to fix 6 cracks. Hope it holds together
0 2012/03/07 19:58:16
Finished. Made 370 rwhp on mustang dyno. Need a lot more. Still seems slow to me. Going to be upgrading the LS6 intake and ported tb for a fast 92/92 or 102/102. This intake is holding me back along with needing to upgrade the exhaust. power is too addictive.
Finished. Made 370 rwhp on mustang dyno. Need a lot more. Still seems slow to me. Going to be upgrading the LS6 intake and ported tb for a fast 92/92 or 102/102. This intake is holding me back along with needing to upgrade the exhaust. power is too addictive.
0 2011/10/03 20:10:33
Almost done
Almost done
0 2011/10/03 20:10:33
Finally getting the heads / cam swap moving along.
Finally getting the heads / cam swap moving along.
0 2011/10/03 20:05:50
I need better pics on the car at night. Made them with a set of LT1 blue tint mirrors to stay true to my '98 blue tinit ones. Want to make a different set soon. Could look better.
I need better pics on the car at night. Made them with a set of LT1 blue tint mirrors to stay true to my '98 blue tinit ones. Want to make a different set soon. Could look better.
0 2011/10/03 20:05:50
Custom brushed stainless pcm cover to prevent water from drenching the pcm. Made it from a stainless dooe off of a grill.
Custom brushed stainless pcm cover to prevent water from drenching the pcm. Made it from a stainless dooe off of a grill.
0 2011/10/03 20:05:50
Fuel pump started going, so upgraded to Racetronix kit
Fuel pump started going, so upgraded to Racetronix kit
0 2010/08/15 10:18:22
Finally finished installing my TRZ moly anti roll bar
Finally finished installing my TRZ moly anti roll bar
0 2010/08/15 10:18:22
0 2009/11/03 08:08:23
new shifter
new shifter
0 2009/11/03 08:08:23
Running new shifter cable
Running new shifter cable
0 2009/11/03 07:57:09
last day before going into hibernation
last day before going into hibernation
0 2009/11/03 07:57:09
new rims
new rims
0 2009/11/03 07:57:09
4l60e out, Header coating lasted 1 year, garbage
4l60e out, Header coating lasted 1 year, garbage
0 2009/07/27 11:16:22
Rigged old school th400 pedal mount kickdown switch to work on tb since it was too tough to squeeze under the the dash and rig it to the pedal. entire setup cost $0.00 to make. Works as good as the $75 Summit ones.
Rigged old school th400 pedal mount kickdown switch to work on tb since it was too tough to squeeze under the the dash and rig it to the pedal. entire setup cost $0.00 to make. Works as good as the $75 Summit ones.
0 2009/07/27 11:16:22
FTI sr0086 3600 stall th400 converter w/ LS pilot extension
FTI sr0086 3600 stall th400 converter w/ LS pilot extension
0 2009/07/27 11:16:22
Finish Line Transmissions beefed up this th400 from our old '76 1 ton tow truck
Finish Line Transmissions beefed up this th400 from our old '76 1 ton tow truck
0 2009/07/27 11:09:32
suspension is coming along
suspension is coming along
0 2009/07/27 11:09:32
Wile swapping the rear, a wasp kept flying under the car. I looked around and noticed a wasp mud nest. Cracked it open and a ton of stunned spiders were packed inside for the baby wasps.
Wile swapping the rear, a wasp kept flying under the car. I looked around and noticed a wasp mud nest. Cracked it open and a ton of stunned spiders were packed inside for the baby wasps.
0 2009/07/27 11:09:32
out with the old, in with the new
out with the old, in with the new
0 2009/07/27 11:03:16
0 2009/07/27 11:03:16
time for the back of the garage
time for the back of the garage
0 2009/07/27 11:03:16
'76 GMC 1 ton truck th400 rebuilt buy Finishline Transmissions. Hughes kit /w Red alto clutches, 4l80e drum, Heavy duty sprag, kolene steels, B&M shift kit, forward falve body. Good to 700 hp
'76 GMC 1 ton truck th400 rebuilt buy Finishline Transmissions. Hughes kit /w Red alto clutches, 4l80e drum, Heavy duty sprag, kolene steels, B&M shift kit, forward falve body. Good to 700 hp
0 2009/04/23 07:55:25
Weld 3.5" x 15" and MT front runners. Also have 15x8's for the rear. Picked them up for a good price locally.
Weld 3.5" x 15" and MT front runners. Also have 15x8's for the rear. Picked them up for a good price locally.
0 2009/04/23 07:55:25
Bringing it home after sawzalling a van in half to get it
Bringing it home after sawzalling a van in half to get it
0 2009/04/23 07:45:55
Cheap junkyard score, will be a 408 some day
Cheap junkyard score, will be a 408 some day
0 2009/04/23 07:37:49
Painted, al new guts, Moser 9, 31 spline, Detroit truetrac, Richmond 4.11's, soon 1/2 studs
Painted, al new guts, Moser 9, 31 spline, Detroit truetrac, Richmond 4.11's, soon 1/2 studs
0 2009/04/23 07:37:49
settin it up
settin it up
0 2009/02/03 18:49:22
9 inch finish paint
9 inch finish paint
0 2009/02/03 18:49:22
Both my rides
Both my rides
0 2009/02/03 18:40:04
oooo
oooo
0 2009/02/03 18:40:04
100 1556
100 1556
0 2009/02/03 18:35:38
crunch!
crunch!
0 2008/12/04 20:29:11
one fine ass...
one fine ass...
0 2008/12/03 11:06:27
The "Transmino"
The "Transmino"
0 2008/12/03 11:00:20
almost hidden
almost hidden
0 2008/12/03 10:56:14
Starting the protection process
Starting the protection process
0 2008/12/03 10:56:14