8.1L Chevy motor
#1
TECH Regular
Thread Starter
Join Date: Jan 2008
Location: Bellaire, TX
Posts: 458
Likes: 0
Received 0 Likes
on
0 Posts
8.1L Chevy motor
Mods, please move if it not in the right spot.
The Chevrolet 8.1 liter engine was produced from 2001-2006 and installed in HD 2500 and larger trucks and vans, as well as motor homes, Suburbans and
Avalanches.
Does anyone know much about this motors?
I can pick one up for a couple hundred dollars out of a wrecked 2003 HD2500.
The Chevrolet 8.1 liter engine was produced from 2001-2006 and installed in HD 2500 and larger trucks and vans, as well as motor homes, Suburbans and
Avalanches.
Does anyone know much about this motors?
I can pick one up for a couple hundred dollars out of a wrecked 2003 HD2500.
#2
They are 375hp and 495 torque Factory so thats pretty good. If you tune them put a good exhaust and cold air I am sure they would be 400hp and well over 500 torque. I am not sure about the Aftermarket fo them but I do believe the block is based on a tall deck big block of old, thats what i have read anyways. They have the same bolt pattern bellhousing as any sbc does or bbc. I Have one at work with 245,000 oilfield miles in a one ton 2001 chevy and it still runs good. It gets about 10 mpg in a 12,500 pound truck thats always loaded to that weight. Surprisingly the only problem is that one of the mounting ears on the tranny which is the allison broke where the transfercase mounts to it but thats about it. I also had to do a cam sensor a while ago but nothing major. I think it is a solid engine but not sure about the aftermarket. How many miles on the motor?
#6
Moderator
iTrader: (20)
I'm wondering why the f*** these things don't have as much aftermarket support. It is almost literally a 496ci, canted valve LS1. They have cathedral ports like the LSx engines, but it's not an inline valve head. There is no conventional distributor, but I hear it has an ignition like an LT1...
I'm trying to get my hands on a set on one and see what I could do. Aftermarket or not, I'd bet you can make an EASY 600whp on pump gas with the iron heads, unless they are just absolute junk. Wild card would probably be the intake, but I hear the marine industry (Arizina Speed & Marine) has something for them.
I'm trying to get my hands on a set on one and see what I could do. Aftermarket or not, I'd bet you can make an EASY 600whp on pump gas with the iron heads, unless they are just absolute junk. Wild card would probably be the intake, but I hear the marine industry (Arizina Speed & Marine) has something for them.
Last edited by KCS; 07-24-2009 at 07:55 PM.
Trending Topics
#8
i would like to see someone build one, but it would be like a boat anchor in the front of most cars. to offset the weight you would have to make some serious power becasue people complain about the extra 88 pounds a iron block adds over the aluminum.
#9
TECH Fanatic
iTrader: (1)
Speaking of "boat anchors"
http://www.hotrod.com/newproducts/hr...ine/index.html
The automotive aftermarket is more comfortable building Gen IV and Gen V BBC engines. For the most part, only the Marine aftermarket has forged ahead with developing the 8100 engines. There, you don't have the tall-deck clearance concerns. Also, a bit of boost can overcome the shortcomings of an OEM cylinder head until demand warrants aftermarket support for the unique design.
With most of the truck tuners embracing diesel performance, the 8100 has been left behind.
http://www.hotrod.com/newproducts/hr...ine/index.html
The automotive aftermarket is more comfortable building Gen IV and Gen V BBC engines. For the most part, only the Marine aftermarket has forged ahead with developing the 8100 engines. There, you don't have the tall-deck clearance concerns. Also, a bit of boost can overcome the shortcomings of an OEM cylinder head until demand warrants aftermarket support for the unique design.
With most of the truck tuners embracing diesel performance, the 8100 has been left behind.
#11
TECH Apprentice
iTrader: (2)
Join Date: Feb 2007
Location: venice/sarasota fl
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
heres a page from a diesel form im on
http://www.dieselplace.com/forum/sho...d.php?t=296939
i think its everything you want to know about the 8.1. theres a guy on the sight doing a cam install on his 8.1, ill read up on it and post that thread if it helps.
http://www.dieselplace.com/forum/sho...d.php?t=296939
i think its everything you want to know about the 8.1. theres a guy on the sight doing a cam install on his 8.1, ill read up on it and post that thread if it helps.