Cast vs. Forged Piston weight.
#1
Cast vs. Forged Piston weight.
Are forged 347 pistons heavier than stock cast. If so, can I remove enough material from the forged piston to make them the same weight as cast pistons with out having to rebalance crank. Motor will be used with at least 200hp shot of direct port nitrous.
Last edited by gollum; 06-05-2005 at 08:02 PM.
#2
TECH Junkie
iTrader: (11)
They are probably lighter. Most forged piston are high performance pistons, which in most cases is a lightweight piston. The cast pistons like stock and aftermarket stock replacement are usually not lightweight. I dont think the forging process adds weight if it heat treating. If its forging done by basicly pounding the metal to make it more dense then I an see it being a little more mass because it will be compressed. But then again I would bet that it would be machined to lighten it back up.
#5
I did a search. OEM MAHLE cast LS1 piston weighs 434 grams. All the forged pistons I found are lighter than the OEM cast piston. So far the JE forged piston part # 194884 is the closest to OEM weight, but is still lighter @430 grams. The new Ross forging part #99838 is claimed to be designed for nitrous use, but Ross did not list the weight on their web site.
#7
Originally Posted by JZ'sTA
Yes you will need to balance this regardless of what aftermarket pistons you use.
Someone does not understand how a crank is balanced.
Last edited by gollum; 06-06-2005 at 05:38 PM.
Trending Topics
#8
TECH Addict
iTrader: (14)
Join Date: Nov 2002
Location: hurst tx
Posts: 2,560
Likes: 0
Received 0 Likes
on
0 Posts
Ok,
You wouldnt "NEED" to balance it. Look at it this way, you are required to have car insurance, but you do not "HAVE" to have it. However if you get into a wreck and dont your "SOL"
Same basic princepal, you need to have the motor balanced, if you dont, it will still run, hell if you get pistons that are lighter, the motor will still run, just not as well.
Take a further look at what your trying to do, if you want to run at least a 200 shot, you should prolly look into doing more than just pistons. That is alot of nitrous, and for longetivitys sake I would say build it right, build it once.
ITS CHEAPER TO DO IT ONCE RIGHT, THAT TWICE WRONG, TWO LEADS TO THREE, AFTER THREE IF YOU DONT DO IT RIGHT, YOUR MACHINE SHOP IS STEALING FROM YOU.
THanks
ed
firebird455@gmail.com
You wouldnt "NEED" to balance it. Look at it this way, you are required to have car insurance, but you do not "HAVE" to have it. However if you get into a wreck and dont your "SOL"
Same basic princepal, you need to have the motor balanced, if you dont, it will still run, hell if you get pistons that are lighter, the motor will still run, just not as well.
Take a further look at what your trying to do, if you want to run at least a 200 shot, you should prolly look into doing more than just pistons. That is alot of nitrous, and for longetivitys sake I would say build it right, build it once.
ITS CHEAPER TO DO IT ONCE RIGHT, THAT TWICE WRONG, TWO LEADS TO THREE, AFTER THREE IF YOU DONT DO IT RIGHT, YOUR MACHINE SHOP IS STEALING FROM YOU.
THanks
ed
firebird455@gmail.com
#9
I once rebuilt an engine (455 Pontiac) USING A DIFFERENT WEIGHT PISTON. The motor was way out of balance and you could feel the engine vibrate badly while seated in the car. The motor eventually spun a rod bearing. I rebuilt the motor a second time, this time balancing the total assembly and rebuilding the big end of the rods on the tight side for more bearing crush. END OF PROBLEM.
Last edited by gollum; 06-06-2005 at 07:36 PM.
#10
TECH Senior Member
iTrader: (18)
Join Date: Jun 2002
Location: NW Houston, TX
Posts: 10,036
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by gollum
I once rebuilt an engine (455 Pontiac) USING A DIFFERENT WEIGHT PISTON. The motor was way out of balance and you could feel the engine vibrate badly while seated in the car. The motor eventually spun a rod bearing. I rebuilt the motor a second time, this time balancing the total assembly and rebuilding the big end of the rods on the tight side for more bearing crush. END OF PROBLEM.
#11
TECH Addict
iTrader: (14)
Join Date: Nov 2002
Location: hurst tx
Posts: 2,560
Likes: 0
Received 0 Likes
on
0 Posts
So wait, youve already had a problem with a out of balance motor, and now your trying to do the same. Or are you trying to say youve learned from your mistake and would rather find a piston that is exactly the same.
Have you looked at Mahle pistons?
Have you looked at Mahle pistons?