78 Datsun 280z-------------> 5.3 Build
#223
well I got the rears cut, but not welded.
Here's how I measured. Looked around, and found that I wanted to cut between 3 and 4". I settled on 3.5. So I made marks at the top of the fender (where the cut would be the deepest) and mounted the flares 1" higher than what I wanted to cut.
I then marked it an inch all the way around, and tapered the edges.
Then I cut the outer layer of sheet metal, and cut it again lower so I could access the inner layer to cut it.
Here is the passenger rear at full tuck.
All the stuff will be here today! Going to be a big day, have an O-chem test wednesday though .... school is taking the back seat to the 280 at this point....
Here's how I measured. Looked around, and found that I wanted to cut between 3 and 4". I settled on 3.5. So I made marks at the top of the fender (where the cut would be the deepest) and mounted the flares 1" higher than what I wanted to cut.
I then marked it an inch all the way around, and tapered the edges.
Then I cut the outer layer of sheet metal, and cut it again lower so I could access the inner layer to cut it.
Here is the passenger rear at full tuck.
All the stuff will be here today! Going to be a big day, have an O-chem test wednesday though .... school is taking the back seat to the 280 at this point....
Last edited by STEEPSS; 04-10-2012 at 10:16 AM.
#232
Well i got a good amount done today.
Camber plates front
and rear
Got my fuel tank installed
ONLY TO FIND IT HAD A ******* HOLE IN IT
so someone will be getting a phone call on monday. no excuse for that as much as i paid for it and as long as i waited.
That's pretty much it. There's a monster thread in suspension and chassis on hybridz.org about the camber plate install for those who are interested.
Camber plates front
and rear
Got my fuel tank installed
ONLY TO FIND IT HAD A ******* HOLE IN IT
so someone will be getting a phone call on monday. no excuse for that as much as i paid for it and as long as i waited.
That's pretty much it. There's a monster thread in suspension and chassis on hybridz.org about the camber plate install for those who are interested.
#234
TECH Addict
iTrader: (3)
Great job on the tail pipe exits! Are you going to smooth off the roll pan or run the bumper? A shortened 69 Camaro bumper would look nice tucked tight right under the tail lights! Sorry to hear about the fuel tank. These after market companies just dont put pride in their work any more. You would think they would have at least pressure tested the tank before shipping. Dont feel alone as I have been left with some inferior products. Bad thing is, you pay good money for these parts and are left with crap. Hope they get the issue resolved and resolved quickly. We want to see this thing in action.
#235
I can get a picture, but its pretty simple. I just drilled 4 holes in the floor, and used large washers on top, with 8mm bolts. You can see the stand-offs in the first pic of the tank.
I'm just going to run it as-is for the time being, and probably just fill the holes and run it like that unless i come across a 240z bumper somewhere. Yeah I'm pretty pissed about the hole in the tank. Its where the shop welded the baffle in. The thing that sucks is that I now have to drain it, hotsy wash it, and either ship it to the shop (in houston) or find someone local to do it. Either way I'm out time and money. I'll call them tomorrow and see if they will just give me some cash so I can get it done local........
Great job on the tail pipe exits! Are you going to smooth off the roll pan or run the bumper? A shortened 69 Camaro bumper would look nice tucked tight right under the tail lights! Sorry to hear about the fuel tank. These after market companies just dont put pride in their work any more. You would think they would have at least pressure tested the tank before shipping. Dont feel alone as I have been left with some inferior products. Bad thing is, you pay good money for these parts and are left with crap. Hope they get the issue resolved and resolved quickly. We want to see this thing in action.