LS2 into my Z32 yehoo
09-20-2016, 12:02 PM
#22
I like where this is going. I loved the z32 I had, except for the underwhelming performance in the acceleration department (2+2 NA car). Should be a well rounded combo with LS power
__________________
Glenn ***
Sales Tech
www.bmrsuspension.com
813.986.9302
Find a Quality alignment shop near you!
Glenn ***
Sales Tech
www.bmrsuspension.com
813.986.9302
Find a Quality alignment shop near you!
09-20-2016, 01:36 PM
#23
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Thanks! I could see an N/A limmo being a bit sluggish, haha
I'm quite excited. Hoping to get it in and do a test fire by sunday. Fingers crossed.
09-20-2016, 08:04 PM
#25
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Got the engine primed tonight and wiring harness routes through the firewall.
I used a harbor freight drill pump and it lasted through 4 quarts of oil until it failed, however in was getting good flow to the top end.
I used a harbor freight drill pump and it lasted through 4 quarts of oil until it failed, however in was getting good flow to the top end.
09-22-2016, 10:38 AM
#28
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
I'll be using the LOJ accessory adapter kit to utilize my 300zx Alternator and PS pump in their stock location on the passenger side of the engine. In the spring I will be adding A/C as well.
09-23-2016, 11:34 AM
#31
this is progressing rather quickly. Looks great!
__________________
Glenn ***
Sales Tech
www.bmrsuspension.com
813.986.9302
Find a Quality alignment shop near you!
Glenn ***
Sales Tech
www.bmrsuspension.com
813.986.9302
Find a Quality alignment shop near you!
09-23-2016, 03:15 PM
#32
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
09-29-2016, 03:18 PM
#35
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Taking the headers to have bung welded in early sat morning. Hopefully if all goes as planned I should do the first test fire Saturday evening. (knocks on wood)
10-04-2016, 02:46 PM
#38
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
10-10-2016, 01:34 PM
#39
Teching In
Thread Starter
Join Date: Aug 2016
Location: Memphis, TN
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
His a short clip taken from my snapchat.
Connected the headers to my existing 2.5" exhaust/H-pipe
<iframe width="560" height="315" src=" " frameborder="0" allowfullscreen></iframe>
Connected the headers to my existing 2.5" exhaust/H-pipe
<iframe width="560" height="315" src="
