PRC stage 2.5 5.3's / MS3 / EWP / 9090 / Bolt Ons / Exhuast
02-23-2007, 08:49 AM
#1
TECH Addict
Thread Starter
iTrader: (29)
Join Date: Apr 2005
Location: Margate, FL
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
PRC stage 2.5 5.3's / MS3 / EWP / 9090 / Bolt Ons / Exhuast RESULTS: 461 RWHP 392 RWTQ
Finally got the car tuned by Jeremy Formato.
Tuning was a bit tricky, and took about an hour and a half to get it really dialed in (dyno and street), still have some bugs to tune out...but we ran out of time...nevertheless, it runs and sounds sick...and oh yeah it HAULS MAJOR ***.
We took it for a street tune after the dyno tune and from 5 k to 7 k it felt like fast forward, that is the only way to explain it...
Mods:
PRC 5.3 Stage 2.5 heads 10.75-1 CR
MS3 237/242 113
EWP
Fast 90 NW 90
March UP
42# green tops/speed inc rails
Racetronix pump
Textralia Exo Skel
t56 Rebuilt tranny
10 bolt, 4.10 gears
*93 octane was used*
*EDIT*
Below is the graph as promised, however it is a photocopy and it is hard to see the numbers on the x and y axis...you get the idea though...not a bad graph, torque picks up at 3000 RPM right around 350 ft lbs if I am reading correctly..enjoy
Dyno Pull 1
http://s8.photobucket.com/albums/a4/...t=MVI_3888.flv
Dyno Pull 2
http://s8.photobucket.com/albums/a4/...t=MVI_3892.flv
Dyno Pull 3 (461/392)
http://s8.photobucket.com/albums/a4/...t=MVI_3893.flv
On the way home with my dad, nailed it from 2nd gear through 4th, just to give you an idea, it SCREAMS
http://s8.photobucket.com/albums/a4/...t=MVI_3898.flv
I am happy, and already want to go faster...i recommend this set up to ANYONE!
SPECIAL THANKS TO: J & J Performance in Ft. Myers, Jeremy Formato, and all the guys who stuck around to see this thing move! Thanks guys!
Finally got the car tuned by Jeremy Formato.
Tuning was a bit tricky, and took about an hour and a half to get it really dialed in (dyno and street), still have some bugs to tune out...but we ran out of time...nevertheless, it runs and sounds sick...and oh yeah it HAULS MAJOR ***.
We took it for a street tune after the dyno tune and from 5 k to 7 k it felt like fast forward, that is the only way to explain it...
Mods:
PRC 5.3 Stage 2.5 heads 10.75-1 CR
MS3 237/242 113
EWP
Fast 90 NW 90
March UP
42# green tops/speed inc rails
Racetronix pump
Textralia Exo Skel
t56 Rebuilt tranny
10 bolt, 4.10 gears
*93 octane was used*
*EDIT*
Below is the graph as promised, however it is a photocopy and it is hard to see the numbers on the x and y axis...you get the idea though...not a bad graph, torque picks up at 3000 RPM right around 350 ft lbs if I am reading correctly..enjoy
Dyno Pull 1
http://s8.photobucket.com/albums/a4/...t=MVI_3888.flv
Dyno Pull 2
http://s8.photobucket.com/albums/a4/...t=MVI_3892.flv
Dyno Pull 3 (461/392)
http://s8.photobucket.com/albums/a4/...t=MVI_3893.flv
On the way home with my dad, nailed it from 2nd gear through 4th, just to give you an idea, it SCREAMS
http://s8.photobucket.com/albums/a4/...t=MVI_3898.flv
I am happy, and already want to go faster...i recommend this set up to ANYONE!
SPECIAL THANKS TO: J & J Performance in Ft. Myers, Jeremy Formato, and all the guys who stuck around to see this thing move! Thanks guys!
Last edited by erikthegoalie; 02-24-2007 at 11:18 AM.
02-23-2007, 09:16 AM
#3
Thats awesome man. I'd love to see a graph.
Mines going in this weekend for a tune and I've got similar mods. Mines an auto, but same cam, TEA 1.5 heads, fast 90, no ewp, 37 lb inj, and racetronix pump also.
Is your fast 90 ported? Any before and after on the ewp?
Mines going in this weekend for a tune and I've got similar mods. Mines an auto, but same cam, TEA 1.5 heads, fast 90, no ewp, 37 lb inj, and racetronix pump also.
Is your fast 90 ported? Any before and after on the ewp?
02-23-2007, 09:51 AM
#4
TECH Junkie
iTrader: (13)
Join Date: Sep 2004
Location: Fort Myers, FL.
Posts: 3,857
Likes: 0
Received 0 Likes
on
0 Posts
very nice indeed. I actually thought that the TQ would of broke 400 but your close enough. I wonder how long it will last till you break the 10 bolt now. You have the bug now and you already want to go faster. haha. You can alsways throw a little juice on there.
02-23-2007, 09:59 AM
#5
Nice power. Look forward to seeing the graph too.
__________________
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
02-23-2007, 10:28 AM
#7
TECH Addict
Thread Starter
iTrader: (29)
Join Date: Apr 2005
Location: Margate, FL
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys thanks a lot....I forgot to add, Fast has a Bo White port....im sure that helped quite a bit...
I am waiting for the 10 bolt to go, then comes a 9 inch...
I have the graph here on paper but I am not sure how to post it...hmmm
I am waiting for the 10 bolt to go, then comes a 9 inch...
I have the graph here on paper but I am not sure how to post it...hmmm
Trending Topics
02-23-2007, 10:29 AM
#8
TECH Addict
Thread Starter
iTrader: (29)
Join Date: Apr 2005
Location: Margate, FL
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 02EBZO6
Thats awesome man. I'd love to see a graph.
Mines going in this weekend for a tune and I've got similar mods. Mines an auto, but same cam, TEA 1.5 heads, fast 90, no ewp, 37 lb inj, and racetronix pump also.
Is your fast 90 ported? Any before and after on the ewp?
Mines going in this weekend for a tune and I've got similar mods. Mines an auto, but same cam, TEA 1.5 heads, fast 90, no ewp, 37 lb inj, and racetronix pump also.
Is your fast 90 ported? Any before and after on the ewp?
I do not have a before and after on the h20 pump...unfortunately...that was a draw back of doing it all at once...but doing it all at once was the biggest PERK, so I just did it...
I love the EWP...works VERY well to cool, easy to install, and picks up power...car pulls hard, trust me
02-23-2007, 11:06 AM
#10
Thats awsome man I think I have to copy you and do about the same setup that exactly what im looking for. Does the car idle really well now you need some new idle clips since its been tuned. Did you get the new injectors in now also and have the duty cylce turned down? I was afraid the ms3 might be too big hows the drivability?
02-23-2007, 11:58 AM
#15
TECH Addict
Thread Starter
iTrader: (29)
Join Date: Apr 2005
Location: Margate, FL
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Billiumss
WOW, great numbers! Tell your tires, "Good Luck" 
I asked Jeremy a few times about the IAC, but he never really answered my question??? I wasn't sure if he heard me or what, but I will see if I can ask him next time I see him...
Anyway, yeah tires=USELESS
02-23-2007, 12:09 PM
#17
TECH Addict
Thread Starter
iTrader: (29)
Join Date: Apr 2005
Location: Margate, FL
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SpdFrk1990
Thats awsome man I think I have to copy you and do about the same setup that exactly what im looking for. Does the car idle really well now you need some new idle clips since its been tuned. Did you get the new injectors in now also and have the duty cylce turned down? I was afraid the ms3 might be too big hows the drivability?
I will get some more clips and add over the next few days! This will include in car, fly bys, digs, highway, idle, WOT etcetc so ya'll can get a good idea what it does and how it sounds...
The MS3 is a great cam, and really stood up to all of its claimed power! @ 7000 RPM the thing STILL was making power, but torque began to drop off...we had to move the limited to 7200...
Streetability is EXCELLENT...honestly, my Textralia Exo Skel is a bit tougher to tame than the cam...that clutch wants MORE AND MORE power..no screwin around with that thing...
I HIGHLY recommend the MS3, it is a great TOP END cam (5000-7000 is REDICULOUS, 3000-5000 is wicked too, but the show is at the top)
Also remeber that I have the 5.3 heads, which really help down low..I honestly have NO problem with the amount of torque at 3000 RPM. I would say cam only you would lose a lot of low end, but if you get the right set of heads, then you can enjoy the top end of the cam but still have MAJOR ***** down low! That is why I love this set up..
If anyone has any questions..or is EVER in the area pm me, I will be more than happy to drive you and let you drive it, its a fun car, tons of useful power..and its sexy as hell too hahaha
I appreciate all the comments fellas, glad my hard work is paying off
Can't wait to see more vids 
