Any tuners in the UK?
#1
Any tuners in the UK?
I'm having some trouble with my car fouling the passenger side plugs and causing the 02 sensor to go bad. Anyone in the UK have the capability to scan and possibly fix what is wrong with my car?
mods:
02 Z-28, !MAF,!CAGS, SLP Lid, stock headers and Y-pipe, LM exhaust
mods:
02 Z-28, !MAF,!CAGS, SLP Lid, stock headers and Y-pipe, LM exhaust
#4
TECH Fanatic
iTrader: (14)
If you got time check on SCT Comes to Germany and go in the announcement section. We are getting ready to have SCT come over and tune 30+ cars on the dyno in a few months.
#6
TECH Resident
Originally Posted by Shinerbock07
Man i bet women over there cream over that american muscle....Wish I was in Europe with my WS.6 I feel like i would get laid ALL THE TIME, because of my car.
I'm in the South of England in Hampshire, If you are local I have scanning software on the laptop I will be happy to take a look.
Trending Topics
#8
I'm in the UK as well, Mildenhall. Dark Blue 2002 WS6. I have the EFI Live software, but I'm not sure if I can register your VIN as well. There is a company at Siverstone raceway that knows a ton about LS1's. They had a lot of Holden cars setting around when I stopped and talked to them.
http://www.wrc-tech.co.uk/
Check under the Vauxhall Monaro tab.... same as a Pontiac GTO.
http://www.wrc-tech.co.uk/
Check under the Vauxhall Monaro tab.... same as a Pontiac GTO.
Last edited by bigblueturtle; 03-24-2006 at 04:55 AM.
#9
I just may hold off until I ship the car in less than 3 weeks. I get my new Bosch 13111's in the mail next week and I'm going to pull the injectors to take a look at them and I'm also swapping the coil packs around to see if that does anything. I'm going to call them anyways and see how much it would cost for them to look at it regardless, if its within my budget I just may take it over there and see what they think. Thanks for the info.
#10
Mmmm, not too many 4th gen. Ls1's
And even less WS6's
And even very less WS6 convertibles !
But they do attract a whole load of attention.
I have driven a full 12 months with no front numberplate, and the cop's just look at the car, and somehow, don't realise, or care that there is no front plate.
I have it under my seat though, just to throw on the dash if the worst comes to the worst.
Anyway, without a front plate, the overhead mororway laser tripod speed cam's can't get you.
Just incase you were a little over the speed limit.
And even less WS6's
And even very less WS6 convertibles !
But they do attract a whole load of attention.
I have driven a full 12 months with no front numberplate, and the cop's just look at the car, and somehow, don't realise, or care that there is no front plate.
I have it under my seat though, just to throw on the dash if the worst comes to the worst.
Anyway, without a front plate, the overhead mororway laser tripod speed cam's can't get you.
Just incase you were a little over the speed limit.
#12
TECH Resident
Originally Posted by WORKSHY
I also could do with gettin my car tuned, but not till after i get a cam in a couple of months!
Just don't trust any of the local backstreet speedshops to do it!
Just don't trust any of the local backstreet speedshops to do it!
#14
TECH Enthusiast
iTrader: (7)
Originally Posted by RedWS6 00
Iim sure Bauer Millet will do it for you, they are up your end of the country. I dont know how much they would charge. I use them for parts. At least if they need a part for the cam install I expect they have it in stock. They know these engines, I wouldn't let any garage change a cam.
#15
TECH Resident
Originally Posted by silversweetZ
Nice looking car RedWS600, where are you at? Are you anywhere near Cambridge?
Further south, about 10 miles north of Portsmouth. Have driven it to Cambrige a couple of times. Have done a little more to the engine bay, need to put some more photos on the site.
Originally Posted by WORKSHY
Possibly but they are quite pricey!don't know if they would do a cam install they couldn't do my headers! They were nice about it, so i had to do the install myself! but wouldn't want to drive it too far to get tuned Baur & Millet are about 30mins away! 16miles!
Last edited by RedWS6 00; 03-27-2006 at 09:28 AM.
#19
12 Second Club
iTrader: (10)
Join Date: Sep 2005
Location: United Kingdom, England
Posts: 343
Likes: 0
Received 0 Likes
on
0 Posts
Hi Andy here Z28 owner Swindon Uk.
Nice web page. Did you catch that Skyline he got a holeshot on you!
What does you car run?
This is my second 4 th gen Camaro I had a 95 Z28 before this one and that was pretty good but this LS1 is awsome!
I haven't been to the drag strip yet. I mostly race a Shakespeare County Raceway
http://www.shakespearecountyraceway.com/events/
Theres a good meet there in May for American cars only RWYB
I may be there this Sunday or Monday Easter weekend as it's RWYB on both days with the ACW SRS series on the Sunday and a Yank V Jap shootout on the Monday.
I have just installed a 125hp Nos kit and I am hoping to get my High Stall TC in this Friday.
Cheers Andy
Nice web page. Did you catch that Skyline he got a holeshot on you!
What does you car run?
This is my second 4 th gen Camaro I had a 95 Z28 before this one and that was pretty good but this LS1 is awsome!
I haven't been to the drag strip yet. I mostly race a Shakespeare County Raceway
http://www.shakespearecountyraceway.com/events/
Theres a good meet there in May for American cars only RWYB
I may be there this Sunday or Monday Easter weekend as it's RWYB on both days with the ACW SRS series on the Sunday and a Yank V Jap shootout on the Monday.
I have just installed a 125hp Nos kit and I am hoping to get my High Stall TC in this Friday.
Cheers Andy
#20
On The Tree
Join Date: Feb 2003
Location: MANCHESTER UK
Posts: 108
Likes: 0
Received 0 Likes
on
0 Posts
bauer millet
Originally Posted by RedWS6 00
Iim sure Bauer Millet will do it for you, they are up your end of the country. I dont know how much they would charge. I use them for parts. At least if they need a part for the cam install I expect they have it in stock. They know these engines, I wouldn't let any garage change a cam.