Rotor Won't Come Off WTF!?
#1
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Sep 2004
Location: Louisville, KY
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Rotor Won't Come Off WTF!?
Update: problem solved.
******************
Some how the driver side rear rotor is jammed on there crooked. I tried threading a nut onto the one of the bottom studs but that didnt do s. I don't get it. I need some advice before I accidentally destroy something.
******************
Some how the driver side rear rotor is jammed on there crooked. I tried threading a nut onto the one of the bottom studs but that didnt do s. I don't get it. I need some advice before I accidentally destroy something.
Last edited by 105; 06-23-2011 at 05:35 PM.
#3
9 Second Club
iTrader: (11)
Join Date: Oct 2007
Location: South Ga
Posts: 1,828
Likes: 0
Received 0 Likes
on
0 Posts
E brake on or you have worn a grove in the rotor when doing burnouts without a line lock. If it is a groove just keep working it back and forth, it will come off just takes a while.
#7
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Sep 2004
Location: Louisville, KY
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Ok. I did release the ebrake before hand, so it must be a groove as I have done burnouts in the past with my line lock at the track. I'll give it another shot tomorrow.
Trending Topics
#8
Get a big hammer, hit the rotor so its back on straight with the hub, and then try to pull it off again. It should come right off. If it doesn't, tap around the outside edge of thne rotor evenly to work it off. Hitting one side of the rotor will just **** it back to where it is now and make it impossible to remove.
#10
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Sep 2004
Location: Louisville, KY
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
After I threaded the nut onto the lower stud to push the bottom of the rotor back on straight, I took the nut off and the bottom edge of the rotor just pushed back out on its own. I never pulled the bottom edge of the rotor out to begin with.
I hope the shop that installed my 9" didn't F something up. This is the first time I've ever taken the rotors off myself.
I hope the shop that installed my 9" didn't F something up. This is the first time I've ever taken the rotors off myself.
#12
Yep take a BFH and knock it back straight and then try to take it off I have always had the worse case scenerios with brake jobs I stopped doing them at other peoples houses becuase of stuff like this I make them bring there cares to me now lol. Oh and some colorful language spoken with a loud tone of voice might help keep your calm!
#13
Save the manuals!
iTrader: (5)
Let's back up a bit...
What did you do before you took the rotor off? Did you change anything with the eBrake or turn the eBrake star wheel? Did you rebuild the eBrake?
Looking at the picture above, it looks like your eBrake release cable is not in the mount hanging down from the axle. Also, I don't recall the backing plate being crooked on the axle flange. Does the other side look the same?
What did you do before you took the rotor off? Did you change anything with the eBrake or turn the eBrake star wheel? Did you rebuild the eBrake?
Looking at the picture above, it looks like your eBrake release cable is not in the mount hanging down from the axle. Also, I don't recall the backing plate being crooked on the axle flange. Does the other side look the same?
#14
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Sep 2004
Location: Louisville, KY
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Let's back up a bit...
What did you do before you took the rotor off? Did you change anything with the eBrake or turn the eBrake star wheel? Did you rebuild the eBrake?
Looking at the picture above, it looks like your eBrake release cable is not in the mount hanging down from the axle. Also, I don't recall the backing plate being crooked on the axle flange. Does the other side look the same?
What did you do before you took the rotor off? Did you change anything with the eBrake or turn the eBrake star wheel? Did you rebuild the eBrake?
Looking at the picture above, it looks like your eBrake release cable is not in the mount hanging down from the axle. Also, I don't recall the backing plate being crooked on the axle flange. Does the other side look the same?
Once I unbolted the brake line bracket from the LCA bracket I was able to slide the ebrake line off of its hook.
#15
TECH Resident
iTrader: (9)
Join Date: Dec 2005
Location: San Jose, CA
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Any brake job I have done where the rear rotors use a shoe-type e-brake has had problems with the rotors sticking. Just take a big rubber mallet and let out all of your frustration out on it, it will come off. A few months ago I did the brake on our FX35 and I had to pry one of the rotors off with a pry bar because it was stuck so bad. This is 100% normal!
#16
Save the manuals!
iTrader: (5)
I didn't change anything with the brakes other than how the shop mounted the lines to my 9", which can be seen here -https://ls1tech.com/forums/suspension-brakes/1436678-ebrake-brake-line-bracket-help.html. These pics also show the passenger side still assembled. The passenger side rotor came off with no problems.
Once I unbolted the brake line bracket from the LCA bracket I was able to slide the ebrake line off of its hook.
Once I unbolted the brake line bracket from the LCA bracket I was able to slide the ebrake line off of its hook.
If that's the case, then a hammer is the only way you can go. Something might break or something may not... If you disconnect the eBrake cable all together so the actuator is completely free, that may help. If the actuator is being pulled in an odd direction, that may be contributing to your issue.
#17
On The Tree
iTrader: (2)
Join Date: Jun 2010
Location: Arkansas
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Hmm...maybe do what you said you did with the lugnut to pull the bottom end back in. Then while its pulled back in, knock the top side out. Then undo the lug nut and see if that helps. Weird that it pops out on its own...
-Will
-Will
#19
On The Tree
iTrader: (1)
Join Date: Jun 2011
Location: Amherst, NH
Posts: 191
Likes: 0
Received 0 Likes
on
0 Posts
Yep, I've had to ruin a few rotors in the past because they were seized onto friends' cars. Most of the time pulling a rotor means you're replacing it with a new set, so that's a green light to bash the hell out of it with a nice hammer. Work back and forth on the rotor, don't just keep hitting one side or you'll get the same crooked effect you have now.
Sometimes leaking a bit of PB blast in between the rotor and the axle will assist the hammer in working it free too. Just remember anything greased that PB hits will need to be re-greased (i.e. brake pad glide surfaces).
Sometimes leaking a bit of PB blast in between the rotor and the axle will assist the hammer in working it free too. Just remember anything greased that PB hits will need to be re-greased (i.e. brake pad glide surfaces).
#20
FormerVendor
iTrader: (73)
Join Date: Jan 2009
Location: Chicago
Posts: 1,731
Likes: 0
Received 0 Likes
on
0 Posts
Simple solution to this: get it back on flush, make sure the ebrake is released and the trans is in neutral. Then SLOWLY spin and pull gently at the same time. It's all about the spinning action, right now the shoes are getting cocked inside the drum so spinning as you pull will prevent that.
Good luck!
Good luck!