FS: 396 Formula
02-25-2008, 04:09 PM
#1
12 Second Club
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Elk Grove Village
Posts: 470
Likes: 0
Received 0 Likes
on
0 Posts
FS: 396 Formula Im moving out to indiana and wont have the time for the car anymore . I have every single document for the car. This car has 18K into it. Here is the part list, the pics and the price. The motor has never been sparyed tho can hold a really good shot never had the urge too. The Body has 89,xxx miles on while the motor, transmission, and rear end only have 7,500 on it.
Engine - 396 Storker Motor
- Eagle 3.8750 stroke crank
- Eagle 6.00" rods
- The block is bored .030 over
- Has splayed 4 bolt main caps
- All arp main bolts and head bolts
- .236/.245 .575/.595 Custom Ground Cam (112 LSA)
- 58MM BBK Throttle Body
- Ported Heads
- Accel Optispark
- Taylor 8MM Wires
- NGK Plugs
- Brand New Coil - 36 LBS Injectors
- New GM Oil Pump
- A/C Delete
- SLP Fan Switch
- SLP Elbow
- Morso CAI
- New Alty and Battery
- New Refab Duralast Starter
- Dnyatech Lontubes into a 3 inch Y-pipe over axle dual SLP Slash Tips (no cats)
- Polyuthren Engine Mounts
- Emissions are GONE
THe car has had regular Oil Changes of 1,500 miles with Royal Purple 10w - 30
motor was dnyotuned at Slingshot Motorsports in Fox River Grove,IL
Dnyo Sheet Avaible to buyer of the car.
Also, have been down to the track many times and have many time slips to prove how fast it is but just like the dnyo sheet the time slips will be to the buyer of the car.
Tranmission - 4L60E (Freshly Redone)
- 2800 Vigilante Stall
- TCI Flexplate
- Brand New Bands, Clutch packs, and just flushed with Royal Purple Trans Fluid
- Transpack Shift Kit
Rear End - 10 Bolt - 3:73 Richmond Gear
- Eaton Posi
- Upgraded Axles
Suspension - Almost Complete- BMR Sub-frame Connectors
- BMR Lower Control Arms
- BMR Panhand Bar
- EdleBrock Torque Arm
- Eibach Front Drag Springs
- Energy Suspension Trans Mount
- New Polyuthren Rear End Bushing
Misc
- Warbird Hood
- LS1 Tail Lights
- Matching Blue vnyle (bird Fill-in, Pontaic Fill-in etc....)
- Limo Tint All around
PICS
The body of the car has no rust. It did have a problem in the shop and has a small crack on the passanger fender, the arm on the lift it what caused it. Other then that there are no Imperfections in the body at all. I can also post a pic of the crack upon request. Right now the car has been sitting, started everyonce in awhile i'd suggest a oil change and possibly collant flush besides that the car is ready to go.
Im asking $9,000 o.b.o started at $11,000
will sell out of state but must be picked up.
Last Night at RSD@GLD 7-13-07
.JPG)
^^^ most recent pic ^^^
I dont want this car to go to someone who wont take care of it. The car is worth every penny and after putting so much time into it i want it to go to someone that really knows about these cars. Any help would be aweasome.
Engine - 396 Storker Motor
- Eagle 3.8750 stroke crank
- Eagle 6.00" rods
- The block is bored .030 over
- Has splayed 4 bolt main caps
- All arp main bolts and head bolts
- .236/.245 .575/.595 Custom Ground Cam (112 LSA)
- 58MM BBK Throttle Body
- Ported Heads
- Accel Optispark
- Taylor 8MM Wires
- NGK Plugs
- Brand New Coil - 36 LBS Injectors
- New GM Oil Pump
- A/C Delete
- SLP Fan Switch
- SLP Elbow
- Morso CAI
- New Alty and Battery
- New Refab Duralast Starter
- Dnyatech Lontubes into a 3 inch Y-pipe over axle dual SLP Slash Tips (no cats)
- Polyuthren Engine Mounts
- Emissions are GONE
THe car has had regular Oil Changes of 1,500 miles with Royal Purple 10w - 30
motor was dnyotuned at Slingshot Motorsports in Fox River Grove,IL
Dnyo Sheet Avaible to buyer of the car.
Also, have been down to the track many times and have many time slips to prove how fast it is but just like the dnyo sheet the time slips will be to the buyer of the car.
Tranmission - 4L60E (Freshly Redone)
- 2800 Vigilante Stall
- TCI Flexplate
- Brand New Bands, Clutch packs, and just flushed with Royal Purple Trans Fluid
- Transpack Shift Kit
Rear End - 10 Bolt - 3:73 Richmond Gear
- Eaton Posi
- Upgraded Axles
Suspension - Almost Complete- BMR Sub-frame Connectors
- BMR Lower Control Arms
- BMR Panhand Bar
- EdleBrock Torque Arm
- Eibach Front Drag Springs
- Energy Suspension Trans Mount
- New Polyuthren Rear End Bushing
Misc
- Warbird Hood
- LS1 Tail Lights
- Matching Blue vnyle (bird Fill-in, Pontaic Fill-in etc....)
- Limo Tint All around
PICS
The body of the car has no rust. It did have a problem in the shop and has a small crack on the passanger fender, the arm on the lift it what caused it. Other then that there are no Imperfections in the body at all. I can also post a pic of the crack upon request. Right now the car has been sitting, started everyonce in awhile i'd suggest a oil change and possibly collant flush besides that the car is ready to go.
Im asking $9,000 o.b.o started at $11,000
will sell out of state but must be picked up.
Last Night at RSD@GLD 7-13-07
^^^ most recent pic ^^^
I dont want this car to go to someone who wont take care of it. The car is worth every penny and after putting so much time into it i want it to go to someone that really knows about these cars. Any help would be aweasome.
02-26-2008, 04:08 AM
#5
What part of IN?
Id keep it, there are a few of us around here that rarley get the cars out.
Ill bet I put on a 100 or 200 miles this summer MAX!!!!!!!!!!!! others that are lucky to do that in a few years. I know one guy that I doubt has put 30 miles on his GN since 2001.
Just hope you don't regret it man, nice car.
Id keep it, there are a few of us around here that rarley get the cars out.
Ill bet I put on a 100 or 200 miles this summer MAX!!!!!!!!!!!! others that are lucky to do that in a few years. I know one guy that I doubt has put 30 miles on his GN since 2001.
Just hope you don't regret it man, nice car.
02-26-2008, 07:54 AM
#6
12 Second Club
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Elk Grove Village
Posts: 470
Likes: 0
Received 0 Likes
on
0 Posts
thanks for compliment, but this car needs to go im moving out to valparsio (sp) and just wanna work with something different. so, im gonna use the money from this car and move out start my life and buy a roller. plus, im getting tired of doing computer tuning with this car, i think im gonna go with something carb next time.
Trending Topics
02-27-2008, 09:47 PM
#15
TECH Enthusiast
iTrader: (13)
Join Date: Feb 2007
Location: near rockford
Posts: 554
Likes: 0
Received 0 Likes
on
0 Posts
Yeah man you should post the numbers since you have before and im sure someone can go back and look. It will help the car sell I think as it is pretty quick
02-29-2008, 04:21 PM
#19
12 Second Club
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Elk Grove Village
Posts: 470
Likes: 0
Received 0 Likes
on
0 Posts
there on another thread awhile back, i can PM them to you guys. i have some other really good ones but the chick would kill me if posted that. haha
i love this site ******* horn ***** who drive fbodys, i fit in so nicely lol
i love this site ******* horn ***** who drive fbodys, i fit in so nicely lol
