This cam will be out next week. Along with the intake and throttle body.

TR 230/224 575/662 on a 110.5 LSA 6K miles on it. I have the cam card and box it came in. 250.00 shipped. SOLD.

Crane dual valve springs good to .650 lift. Same miles as cam. 160.00 shipped.

Walbro 155 inline fuel pump with wireing. 90.00 shipped.

Stock intank pump 65.00 shipped.

LS6 intake 10K miles on it. 330.00 shipped. SOLD.

HPM chassis mount TQ arm, red in color and the chassis mount is black. Has been modified slightly. The hole were the arm mounts to the brkt has been moved forward about 1" for a 9" rear. It will work absolutely fine on and car.200.00 + shipping.

BO White ported throttle body 175.00 + shipping.SOLD to Bo.

Stock fuel rails and injectors. 200.00 + shipping.

Spec stage 3 with billet steel fly wheel half life left on it, 200.00 + shipping.

10 bolt rear with a broken 3 series carrier, 4.11's new, LCA relocation brkts, no back plates. 40.00 come get it. SOLD


Stock 3.42's for a 3 series carrier 40K miles. 75.00 + shipping.

TR chromoly push rods 7.4". I'm not sure if I going to need these, if not then 75.00 shipped. I won't know for a few weeks. Sorry.

Carbon fiber tail lights with clear lens. 80.00 + shipping. SOLD.

Mid raise car lift, hydrolic power by a electric pump, 110 volt wall plug, bolts to cocreate floor. works great 500.00 come get it, to heavy to ship. pics are down lower.

Add the 3% if using paypal. I may be adding things vey shortly. I can put up some pics of these things if requested. PM me please.

 

pushrods used? pm me i might want tem

 

Yeah with about 6K miles on them. I do not know if I need these or not. If they will not work with my milled heads I will have to get shorter one. I will know in the next two weeks.

 

I will take the intake sending PM now...

 

just let me know.

 

i will let you know it a week or two, thanks.

 

 

Car lift just added to the list. 500.00

 

Be sure to let who ever know that I will redo the port on the TB if they arent gonna run a power ring

 

think the TA will clear TSP TD's? have you ran the TA on slicks with no problem?

 

Absolutely Bo, As he said,the TB was ported with a TNT ring on it. So the opening of the TB could use a tad bit more work on it.

You could send it to bo and he will clean it up a bit. Thanks Bo. Sorry to see you back to not taking orders anymore. I figured you would get over welmed with work again.

 

I'm not sure about that. Some work may have to be done to go under the chassis mount as the area looks just enough for one 3" pipe to pass through next to the drive shakt loop.

 

i am located in indy....and i am interested in the cam, springs and the pushrods. send me a PM with a "packaged" price and we might be able to work something out.

 

PM sent.

 

Will the HPMotosport TA work with my stock rear end on my 02 Z28? In looking at the pics I am wondering how that brace works - it looks like it attaches at 3 points? The two bolt holes from the stock cross brace and a 3rd one somewhere behind and on the drv's side? Do you have a link to thier website/arcticle showing this TA installed? Or maybe just more pics on your car with a wider view of what is going on? I have a 3" ORY into a 3" CB - should clear no problem?
Thanks - stevet

 

The exhuast will work fine and yes it will fit a stock rear or a 12 bolt rear just fine.
The other brkt goes to the lt rear control arm bolt and there is another bolt that goes through the seat belt bolt on the floor. It is VERY a sturdy mount.
I have all the instructions.
Part# HPM-5750-AZ

I don't see a web site on the instuctions but I'm sure there out there.

 

Ttttt

 

MAN I JUST BOUGHT THAT SAME CAM and springs but the .600 single not dual for $575 with the locks titanium locks and and guides

im wondering IF I GOT RIPPED OFF?......naw its kool i freaking love that 230/224....i would recommened it any day of the week....bump

 

will it fit on a Moser 9"?

send me some more in depth pictures so i can see how this thing bolts up as a whole. I am pretty interested here.....only thing that worries me is the mount in the front. I've already broken one TA, and i really don't wanna break another one...

timakersbba@hotmail.com

 

It will fit but if the car is lowwered at at you will have problems. Thats why I took it off. The mount on the front of the 9" makes it sit to close to the tunnel and it will hit.

It was made for a 10 or 12 bolt.