Is welding aluminum block possible ?
#1
Launching!
Thread Starter
iTrader: (3)
Join Date: Jul 2005
Location: West Haven, CT
Posts: 283
Likes: 0
Received 0 Likes
on
0 Posts
Is welding aluminum block possible ?
Ls2 block, piece of outer starter bolt hole broke off due to overtorquing I assume. Can the piece be aluminum welded back on ?
Thanks
Ron H
Thanks
Ron H
#4
Launching!
Thread Starter
iTrader: (3)
Join Date: Jul 2005
Location: West Haven, CT
Posts: 283
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MetallicaMatt
might want to consider making some kind of brace, using the other starter bolts to hold the brace. might be an easier and safer method than welding the block
just my 2cents
just my 2cents
#5
Staging Lane
Join Date: Apr 2005
Location: Coastal NC
Posts: 93
Likes: 0
Received 0 Likes
on
0 Posts
I have seen welding repairs made to aluminum heads for cars, outboard motors, small aircraft (aluminum) engine blocks and aluminum diesel engines. I have never seen it attempted without all parts stripped, and the piece to be repaired cleaned repeatable until its spotless. Usually it is wrapped in thermal blankets with just the area to be welded open to the air, and then it is flooded with excess argon gas and TIG welded.
Oh yeah the welder always tries to get the area to be welded as level as possible, stopping to move the object as needed. I have never seen anyone try an overhead repair. But I have seen some vertical repairs done to stripped bolt holes in the hull where the final drive (connects the transmission to the tracks) bolts to on the aluminum armor on the amphibious tractors that the USMC has, it was a bitch.
I really think it would be best to pull the engine and strip it down it you try to get it welded. If you do that heck rebuild the engine with another block But what the heck do I know? It may be possible for it to be welded in place.
Oh yeah the welder always tries to get the area to be welded as level as possible, stopping to move the object as needed. I have never seen anyone try an overhead repair. But I have seen some vertical repairs done to stripped bolt holes in the hull where the final drive (connects the transmission to the tracks) bolts to on the aluminum armor on the amphibious tractors that the USMC has, it was a bitch.
I really think it would be best to pull the engine and strip it down it you try to get it welded. If you do that heck rebuild the engine with another block But what the heck do I know? It may be possible for it to be welded in place.
#6
Launching!
Thread Starter
iTrader: (3)
Join Date: Jul 2005
Location: West Haven, CT
Posts: 283
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Diamond Jim
I have seen welding repairs made to aluminum heads for cars, outboard motors, small aircraft (aluminum) engine blocks and aluminum diesel engines. I have never seen it attempted without all parts stripped, and the piece to be repaired cleaned repeatable until its spotless. Usually it is wrapped in thermal blankets with just the area to be welded open to the air, and then it is flooded with excess argon gas and TIG welded.
Oh yeah the welder always tries to get the area to be welded as level as possible, stopping to move the object as needed. I have never seen anyone try an overhead repair. But I have seen some vertical repairs done to stripped bolt holes in the hull where the final drive (connects the transmission to the tracks) bolts to on the aluminum armor on the amphibious tractors that the USMC has, it was a bitch.
I really think it would be best to pull the engine and strip it down it you try to get it welded. If you do that heck rebuild the engine with another block But what the heck do I know? It may be possible for it to be welded in place.
Oh yeah the welder always tries to get the area to be welded as level as possible, stopping to move the object as needed. I have never seen anyone try an overhead repair. But I have seen some vertical repairs done to stripped bolt holes in the hull where the final drive (connects the transmission to the tracks) bolts to on the aluminum armor on the amphibious tractors that the USMC has, it was a bitch.
I really think it would be best to pull the engine and strip it down it you try to get it welded. If you do that heck rebuild the engine with another block But what the heck do I know? It may be possible for it to be welded in place.
This just pisses me off to no end ....
#7
TECH Addict
iTrader: (16)
Join Date: Jul 2004
Location: Nevada, TX
Posts: 2,218
Likes: 0
Received 0 Likes
on
0 Posts
You want to preheat the area to a nominal temperature(not hot enough to warp), and bevel out the piece to go back on. Be sure and get full penetration of the weld and it will be fine. If the weld is just on the surface it will break again. Do not use a spool gun, use a tig. Make sure that you have an actual skilled weldor do the work, and not some hack. This is coming from a guy that has fixed alot of random aluminum, cast and billet.
Trending Topics
#8
TECH Fanatic
iTrader: (8)
Join Date: Oct 2003
Location: I like BoomBoom !!
Posts: 1,753
Likes: 0
Received 0 Likes
on
0 Posts
In theory, you could fix it in the car. Is it a brand new block that's never been used? What happens with aluminum is......it's actually porus, and over time absorbs oil from the internal parts. You can sprey it with brake parts cleaner, and it looks nice, and clean. But.... put some heat to it, and the oil is drawn out of the pores to the heat source, contaminating the weld, and driving the welder CRAZY!!! If the block's never been used, I'd say it could probably be repaired with a minimum of hassle. If it's been used, then your chances might be 50/50 on doing it IN the car. Sorry
#9
12 Second Club
iTrader: (28)
Join Date: Feb 2005
Location: Quad Cities, IA
Posts: 858
Likes: 0
Received 0 Likes
on
0 Posts
A lot of people weld aluminum blocks... Very safe, I've even seen a piston go through the side of a block and they welded it back up (of course the guy was running sleeves). Go for it, but I'd probably have someone who has experience welding on blocks do it.
#10
Launching!
Thread Starter
iTrader: (3)
Join Date: Jul 2005
Location: West Haven, CT
Posts: 283
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by wkdivr
In theory, you could fix it in the car. Is it a brand new block that's never been used? What happens with aluminum is......it's actually porus, and over time absorbs oil from the internal parts. You can sprey it with brake parts cleaner, and it looks nice, and clean. But.... put some heat to it, and the oil is drawn out of the pores to the heat source, contaminating the weld, and driving the welder CRAZY!!! If the block's never been used, I'd say it could probably be repaired with a minimum of hassle. If it's been used, then your chances might be 50/50 on doing it IN the car. Sorry
#12
Banned
iTrader: (10)
Originally Posted by wkdivr
In theory, you could fix it in the car. Is it a brand new block that's never been used? What happens with aluminum is......it's actually porus, and over time absorbs oil from the internal parts. You can sprey it with brake parts cleaner, and it looks nice, and clean. But.... put some heat to it, and the oil is drawn out of the pores to the heat source, contaminating the weld, and driving the welder CRAZY!!! If the block's never been used, I'd say it could probably be repaired with a minimum of hassle. If it's been used, then your chances might be 50/50 on doing it IN the car. Sorry
#13
10 Second Club
iTrader: (11)
TIG on aluminum FTW. I have a little cousin that is a welder by trade. He is still going to school, but his instructor says he is miles ahead of most experienced people. He says he can cut an aluminum can in half and tig it back together. Your block is easily fixable and can be made to be stronger than it was before it broke. Find a reputable welder and talk to them.
#14
Launching!
iTrader: (1)
Join Date: May 2006
Location: Solon, Ohio
Posts: 291
Likes: 0
Received 0 Likes
on
0 Posts
couldnt you just helicoil it?
it would be easier (at least i think so!)
or drill out the threads and tap for a bigger bolt and just drill the starter and shims out bigger then use a bigger bolt
sometimes easier is better
it would be easier (at least i think so!)
or drill out the threads and tap for a bigger bolt and just drill the starter and shims out bigger then use a bigger bolt
sometimes easier is better
#15
if you can get to pa my welding instructor welds aluminum like theres no tomorrow, if i ever needed anything important welded he would be the guy to goto, i thought i knew welding till i saw this guy go at it
#16
Launching!
Thread Starter
iTrader: (3)
Join Date: Jul 2005
Location: West Haven, CT
Posts: 283
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ggk
couldnt you just helicoil it?
it would be easier (at least i think so!)
or drill out the threads and tap for a bigger bolt and just drill the starter and shims out bigger then use a bigger bolt
sometimes easier is better
it would be easier (at least i think so!)
or drill out the threads and tap for a bigger bolt and just drill the starter and shims out bigger then use a bigger bolt
sometimes easier is better
Thanks
Ron
#18
6 & 8 Second Club
Join Date: Aug 2006
Location: Illinois, RT 66 dragway area
Posts: 2,284
Likes: 0
Received 0 Likes
on
0 Posts
You can weld any part of an alum block. Any part u can get a torch to I meant. I've seen some junk *** crap that came back like new. Fuel motors and Pro-Mod stuff can get really blown up good. It must be done by an expert with experience. Alum is much harder to weld than steel, especially at a load point like that. If done correct, it will be stronger than new, because it will be less porous. Good luck, be careful with big talkers, get someone good.