99 frc c5... 807rwhp f1a... Corvette cover car
#1
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Feb 2012
Location: hammond louisiana
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
99 frc c5... 807rwhp f1a... Corvette cover car
I bought this car for 25k about 6 weeks ago .
Bought a brand new f1a procharger 3k
New ecs tranny brace $400
Big brake kit $800
New hub bearings and spindle
New motor/trans mounts
New plugs and all new fluids!
Fixed "reduced engine power" which ment new tac module and throttle body harness.
New front tires and alignment !
I'm right at 34k in this car now.
There is another car I want so i am cutting my losses.
Blower still has 11 month warranty
Asking 29k
For more question and serious buyers 985-634-5859
Thanks
Engine:
414ci LS2 9:1CR
Callies Crank
Callies Rods
wiseco pistons/rings
Lingenfelter 6.0 Heads
CB02 Blower cam
Comp 921 springs
ARP head studs
Hardened Pushrods
Induction:
Procharger F1-A
car is low boost at 10psi on 93 tune/made 807HP/710TQ
Cartek Flip Drive (Dual belt setup)
8 Rib crank and blower pulleys as well (Zero belt slip)
Tial 50mm BOV
Fuel:
RSI Fuel system
Twin in-tank Walboro 255lph pumps
Two -6 Feed lines
Return is a single -6
Aeromotive Fuel rails
Aeromotive Regulator
83# injectors
Exterior:
MCM Carbon Fiber Hood
L5 Rear fenders
Specter Works rear facia
iForged Aero Rims 18x9.5 & 19x13 ($6000 in just rims)
BFG 275/35/18 up front, Nitto NT05R 345/30/19 rear
Exhaust:
LG Pro Long Tube Headers
LG catless x-pipe
Borla Stinger quad tip exhaust
Drive train
RPM Level V Transmission and then some
Gforce overdirve gearset .83/.70
B&M Ripper Shifter
LG Solid torque tube bushings
Hardened output shafts
Stock 3.42 gearing
Monster stage 5 clutch
Misc:
AEM Wide band gauge in pillar pod
Boost Gauge in pillar pod
Line Lock in car just not hooked up
Slotted & Dimpled Rotors
HID headlights (lows) Stock Highs
Car Skinz gray stitched center console
Car Skinz gray stitched shift boot
Black chrome engine cap set
Lingenfelter battery relocation to trunk kit
Z51 Suspension
Covercraft Dustop Car Cover
2 Sparco 6 Point Harnesses/stock seat belts still in car
Bought a brand new f1a procharger 3k
New ecs tranny brace $400
Big brake kit $800
New hub bearings and spindle
New motor/trans mounts
New plugs and all new fluids!
Fixed "reduced engine power" which ment new tac module and throttle body harness.
New front tires and alignment !
I'm right at 34k in this car now.
There is another car I want so i am cutting my losses.
Blower still has 11 month warranty
Asking 29k
For more question and serious buyers 985-634-5859
Thanks
Engine:
414ci LS2 9:1CR
Callies Crank
Callies Rods
wiseco pistons/rings
Lingenfelter 6.0 Heads
CB02 Blower cam
Comp 921 springs
ARP head studs
Hardened Pushrods
Induction:
Procharger F1-A
car is low boost at 10psi on 93 tune/made 807HP/710TQ
Cartek Flip Drive (Dual belt setup)
8 Rib crank and blower pulleys as well (Zero belt slip)
Tial 50mm BOV
Fuel:
RSI Fuel system
Twin in-tank Walboro 255lph pumps
Two -6 Feed lines
Return is a single -6
Aeromotive Fuel rails
Aeromotive Regulator
83# injectors
Exterior:
MCM Carbon Fiber Hood
L5 Rear fenders
Specter Works rear facia
iForged Aero Rims 18x9.5 & 19x13 ($6000 in just rims)
BFG 275/35/18 up front, Nitto NT05R 345/30/19 rear
Exhaust:
LG Pro Long Tube Headers
LG catless x-pipe
Borla Stinger quad tip exhaust
Drive train
RPM Level V Transmission and then some
Gforce overdirve gearset .83/.70
B&M Ripper Shifter
LG Solid torque tube bushings
Hardened output shafts
Stock 3.42 gearing
Monster stage 5 clutch
Misc:
AEM Wide band gauge in pillar pod
Boost Gauge in pillar pod
Line Lock in car just not hooked up
Slotted & Dimpled Rotors
HID headlights (lows) Stock Highs
Car Skinz gray stitched center console
Car Skinz gray stitched shift boot
Black chrome engine cap set
Lingenfelter battery relocation to trunk kit
Z51 Suspension
Covercraft Dustop Car Cover
2 Sparco 6 Point Harnesses/stock seat belts still in car
#5
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Feb 2012
Location: hammond louisiana
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
I always wanted a c6z ! And one has came up for sale. Like said above tho... If it sells before mine I will keep mine!
Been driving it all day today! Doesn't happen much in louisiana with our weather!!
Bump
Been driving it all day today! Doesn't happen much in louisiana with our weather!!
Bump
#6
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Feb 2012
Location: hammond louisiana
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
Morning bump ....
Have a few serious buyers coming to look at the car this week but no cash in hand yet.
Just want to make it clear that this car is on 10pbs of boost with a 4.38 pulley... Put down 807 rwhp on boost alone.
No meth "which was my next mod" . This blower is barely humping on 10lbs on this cubic inch motor.
So if u want more power a simple pulley swap or meth is all you need. Honestly I'm happy with the power on the street so i wasn't interested in doing a pulley swap. I was gonna install meth for safety purposes not to gain any power.
Have a few serious buyers coming to look at the car this week but no cash in hand yet.
Just want to make it clear that this car is on 10pbs of boost with a 4.38 pulley... Put down 807 rwhp on boost alone.
No meth "which was my next mod" . This blower is barely humping on 10lbs on this cubic inch motor.
So if u want more power a simple pulley swap or meth is all you need. Honestly I'm happy with the power on the street so i wasn't interested in doing a pulley swap. I was gonna install meth for safety purposes not to gain any power.