evilZO6

iTrader: (4)

So i just ran across this on cardomain. I absolutely hate the fron end but look at that! A widebody firebird! Everything from the front fenders back is amazing!!! Anyone have anymore info? Its a little wavy but still amazing!
http://www.cardomain.com/ride/2600892

The Alchemist

iTrader: (19)

I've seen that before, there was a thread back in the summer I think.

I wish GMMG would have done a similar trans am version to their DH camaro's.

Flaring Afro

is it just me or does that look not much wider than stock? also not a fan of the mesh at all.

evilZO6

iTrader: (4)

It olooks way wider to me. If you read it, he gives dimensions. i think he says like 6-7 inches. You cant go too wide without it looking ridiculous on our cars

Flaring Afro

^ no i looked again and he said 1" front, 1.5 rear. not sure if each front wheel is .5 to make 1 or not. 6-7 inches would be ridiculous. the car wouldnt fit on the road.

evilZO6

iTrader: (4)

[QUOTE=Flaring Afro;11051007]stance, she ranges 6 to 8 inches wider than stock (depending where you measure). Wheels have been pushed out 1 inch in the front and 1.5 inches in the rear. QUOTE]


theres still distance from the wheels to the outside of the fender lip.

evilZO6

iTrader: (4)

Any hope you could dig it up? I'm looking but not seeing anything!

MUSTANGBRKR02

iTrader: (91)

that thing looks silly. the body doesn't flow at all. It may just be the car or prep work but i don't like it.

C-Sicz

Not a fan. One accident and that will be a nightmare with everything molded together like that

evilZO6

iTrader: (4)

True!! I agree i hate the fact that he molded all the bumpers and fenders. Stupid mistake. one little bump and hes going to regret it

The Alchemist

iTrader: (19)

Sorry, I couldn't find the thread, but it was this car that was the subject of that old thread. It was probably in one of the camaro widebody threads and someone brought up this car as a firebird example.

1995blacktattop

iTrader: (2)

Rai

looks great!

very mean - i would just remove the groundfxs

blindxeyed

iTrader: (8)

Repost..

https://ls1tech.com/forums/appearanc...e-body-ta.html
https://ls1tech.com/forums/appearanc...yesterday.html

Big Bird WS6

iTrader: (9)

i think it is a great idea. and i would never mold it together. but i would love to add 2" to front and 3" to rear

Big Bird WS6

iTrader: (9)

well i have talked to a few places. one one guy told me that they could build 50 sets of wide body kits for our cars. front bumper, rear bumper, front fenders and rear fends, and side skirts for around 1500 a set. but i didnt have the funds to say "ok" lol

1_bad_TA

iTrader: (6)

I think it looks like ***.

JasonWW

iTrader: (2)

In order for it to look right, you would have to add a door overlay. Otherwise it is not going to flow properly.

ghost_ride_the_whip

i like the look, but i dont like the front but the back looks good

69TA

iTrader: (263)

needs to lose the ground effects and hood, front grille b.s.

also can't tell but it looks like he almost went straight down like behind

the rear tires.

I know it's hard as hell but he should have tried to stay in keeping with

voluptuosness (curvey hour glass feel of a TA body)