Side Splitters ready for sale...
TECH Enthusiast
Joined: Feb 2009
Posts: 650
Likes: 2
From: Schaumburg, IL
I gotta say that looks pretty good, better than I thought it would look.. If you get the front splitter and the canards all powdercoat Wet Black it would look damn good.
Speaking of that, does your front splitter material hold up to high heat?
Speaking of that, does your front splitter material hold up to high heat?
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
No but we can make the splitter out of any material you want. We can also make it and the canard all one piece (in a metal, not in the ABS)...
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
It is wavy in some places because I forgot to put spacers back in when I did the canard test (forgot to tighten a bolt here and there if you look hard enough
). LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Front canards look great and I imagine the rear canards looking good as well. I'm gonna end up putting these on before the brake conversion I just got from you lol.
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
I found a spacer set in the back of my car and am wondering where in the hell it came from
Edit
I just opened it right now, it's all there.
But I think I'm short a small washer and a set of instructions lol.
I just opened it right now, it's all there.
But I think I'm short a small washer and a set of instructions lol.
Last edited by Andros; May 22, 2009 at 01:09 AM.
mind if i ask where you buy sheets of ABS like that? i have been meaning to make some stuff for my car (mostly gauge mounting panel) but am having trouble finding material that will match the interior dash and whatnot.
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
You just unbolt your four factory bolts and bolt the bracket on, then bolt the caliper to the bracket and make sure you slide the spacers on 
I must have made my machinist cut spacers I already had then
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
Couldn't wait to put the canards on so I did it tonight... Tried to take pics, thought they came out ok but they SUCK
Here they are anyways...
Working General Hospital tomorrow and have to try to get out to Sun Valley to pic stuff up for Invasion... I'll try to get pics before the sun goes down but no promises.
Looks 1000xs better in person though (with the canards)
Here they are anyways...
Working General Hospital tomorrow and have to try to get out to Sun Valley to pic stuff up for Invasion... I'll try to get pics before the sun goes down but no promises.
Looks 1000xs better in person though (with the canards)
