Emblemros.com two week site wide sale
11-16-2009, 09:09 PM
#43
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
What is your name? If you bought them after I announced the sale I will give you the discount as a refund. I just need to check your order.
We were letting everyone know in multiple postings we were going to do this sale. We just did not know all of the final details at the time.
Let me know and I will check.
Thanks, Roger
11-17-2009, 08:48 PM
#47
Can you do an exact replica of the C5 Z06 badges but instead of the Z 06 have the Z 28 in the same font and even have the 405 HP below it just like the '03-'04 C5 Z06 badge? Mastech used to do an emblem like that, but it was POOR quality. If you could do something like this in stainless, I would be VERY interested if the price wasn't too prohibitive. I just orderd C6 Z06 style Z28 emblems, but I really would like the C5 style better.
11-17-2009, 09:33 PM
#48
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
Can you do an exact replica of the C5 Z06 badges but instead of the Z 06 have the Z 28 in the same font and even have the 405 HP below it just like the '03-'04 C5 Z06 badge? Mastech used to do an emblem like that, but it was POOR quality. If you could do something like this in stainless, I would be VERY interested if the price wasn't too prohibitive. I just orderd C6 Z06 style Z28 emblems, but I really would like the C5 style better.
We made a few sets of the C5 version in the past, but they never really took off. Those were domed in the center, and were machined or cast that way. We just made a flat version of it. Looked very nice, but not the 3D look you will get from machining a block of aluminum. Unless you would like them in the flat version.
Thanks, Roger
11-17-2009, 10:11 PM
#50
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
Clean it up with goof-off, and alcohol afterwards. Then remove the liner on our piece, and stick it on.
Then you get a camera and send me a picture.
11-17-2009, 10:13 PM
#51
TECH Fanatic
iTrader: (10)
Join Date: Mar 2008
Location: San Antonio
Posts: 1,448
Likes: 0
Received 0 Likes
on
0 Posts
Heat your factory piece up with a hair dryer, "NOT A HEAT GUN". When the adhesive gets warm it will get pliable, and you can pull off the factory piece.
Clean it up with goof-off, and alcohol afterwards. Then remove the liner on our piece, and stick it on.
Then you get a camera and send me a picture.
Clean it up with goof-off, and alcohol afterwards. Then remove the liner on our piece, and stick it on.
Then you get a camera and send me a picture.
11-18-2009, 03:20 PM
#52
We made a few sets of the C5 version in the past, but they never really took off. Those were domed in the center, and were machined or cast that way. We just made a flat version of it. Looked very nice, but not the 3D look you will get from machining a block of aluminum. Unless you would like them in the flat version.
Thanks, Roger
Thanks, Roger
Thanks!
My C6 Z06 style Z28 emblems arrived today and they look GREAT! Still interested in getting C5 version though.
11-20-2009, 08:47 PM
#60
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
This picture is more than 4 years old. and we would make this much different now.
It is absolutely all I have of this piece.