Mista Blazer

iTrader: (4)

How was the install for the fuel pressure? did you put it on the end of the fuel rail?

JoshuaGrooms83

iTrader: (2)

yep, like so

was real easy

heres where the ecetronic portion of the boost gauge is.

Schantin

iTrader: (6)

Here's my old setup.

mcalus

iTrader: (14)

V61ST48

Great fiberglass work sir.

mcalus

iTrader: (14)

Thanks! Although, no glass was used. Just plastic repair and some glaze.

mikh338

iTrader: (16)

has anyone run a mechanical nitrous guage into a pillar pod? im trying to figure how many ft of nitrous line ill need to hook it up from the engine bay. im guessing 4-6ft? got all my autometer phantom guages, the tripple pod will be here tomorow so ill post pics up

Flubyux2

No one has a gauge pod for the center stack??

I hate pillar pods. Too ricey... And I have supras lol. Ironically, I do use pillar pods in diesel trucks because it's completely irrelevant about what people on the outside think... It's a truck and the gauges are work-related IMO.

Last time I had a pillar pod, was in my awd turbo dsm back in 2001. It attracted way too much unwanted attention. Everyone and their brother singled me out onthe streets and tried to race me. That said, I'd love to have a pod above the Ac vents for oil temp, boost and fuel pressure.

juSStin4171

iTrader: (2)

I'm going to make a new fiberglass t-top roof liner with the guages built into the area either above the rearview mirror or in place of the sun visor that I never use. Should be interesting, I'll post up if/when I get around to actually building it.

mikh338

iTrader: (16)

finally got my gauges in last week here are a few pics. autometer phantom nitrous guage mechanical and matching digital shift light stage 2. also a AEM wideband. the triple pillar pod I am very upset with, its a bradn new autometer pod for ttops and you will see what im very mad about
[IMG][/IMG]
[IMG][/IMG]
this pic is why im mad. the entire side has a huge hole and where my vent comes out of the stock pillar is a much larger hole then the stock pillar has so I cant get my vent trim piece onto this pod and just looks terrible. pretty pissed for spending $60 on this and looking like this
[IMG][/IMG]

99'CajunFirehawk157

iTrader: (57)

Autometer single...

88blackiroc

iTrader: (3)

Here's mine soon to be installed
And what a pain to make that clunky eboost2 fit! It'll be worth it though!

Cole Train

iTrader: (30)

I am doing a 4L80 swap and decided to do a pillar pod. I don't care for them but needed a place to put a trans-temp gauge. I went with a GlowShift because i liked the blacked out look when they are off and they aren't overpriced. Did an autometer single pod for it so it's not overly noticeable. It helps i have dark tint on the car as well

mcalus

iTrader: (14)

Lol send that thing to the trash and buy one of my setups!

silverWS.6

iTrader: (1)

My lonely gauge

Tipnitty

iTrader: (3)

Man I'm about to buy an autometer pod but I don't want it to look like this. That's really concerning.

Rise of the Phoenix

iTrader: (27)

Buy a glowshift 3 gauge pillar pod. That's what I have, and trust me, looks about 10x better than that sorry excuse for a pillar pod.

Tipnitty

iTrader: (3)

Was it one that you had to hack up the stock pillar as well?

Rise of the Phoenix

iTrader: (27)

Not sure what you mean by "hack up", but it does go on top of the a pillar, but loks stock when done right. It fits great and looks much better than that other one.

Tipnitty

iTrader: (3)

I meant having to cut holes and drill into the stock pillar. But I think you have to will all the pods for the fbody. But I ordered the glowshift one.