Emblempros.com September Sale
#64
Stop I can't afford all this.
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
#65
Thread Starter
FormerVendor
iTrader: (32)
Joined: Jul 2003
Posts: 3,654
Likes: 0
From: Lexington, KY
Stop I can't afford all this.
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Per my email instructions, you need to make sure the parts shape matches the curvature of the vehicle where you want to place it.
this is something that needs to be done by the customers, because we do not know where parts will be placed, and even on the back of this car the curvature changes the farther fro m the center you go.
So once you select a location, a very slight adjustment by hand might be needed prior to adhesion.
#67
I might get some flak for this but I've kind of always wanted a custom RPO sheet in stainless. I'd have to come up with some of the RPO's though as I'd like it to apply to the cars current state rather than its v6 auto w68 call out. Car is practically a 1of1 at this point
Last edited by blackbyrd; 04-16-2017 at 09:49 PM.
#69
Thread Starter
FormerVendor
iTrader: (32)
Joined: Jul 2003
Posts: 3,654
Likes: 0
From: Lexington, KY
I might get some flak for this but I've kind of always wanted a custom RPO sheet in stainless. I'd have to come up with some of the RPO's though as I'd like it to apply to the cars current state rather than its v6 auto w68 call out. Car is practically a 1of1 at this point
Should not be any problem doing it.
Thanks, Roger
#72
#74
I have a question above it the 5h gen Z28 emblem, would it cover over the whole space once I remove my Z28 emblems.
I'm afraid of what I'll find once I remove them, but want to upgrade to something different
I'm afraid of what I'll find once I remove them, but want to upgrade to something different
#77
Thread Starter
FormerVendor
iTrader: (32)
Joined: Jul 2003
Posts: 3,654
Likes: 0
From: Lexington, KY
There should be no issues removing your stock parts. What is behind them is just clearcoat and paint. The fishing line trick works nice and fast.
Please let me know
#80
Hi, my wife has an 05 S197 Mustang GT with a roush supercharger, looking for ideas for supercharged emblems, what could you do for me please and also colour options, thanks colin.