Nobody really sees that area anyway. 
Rusty Hinge!?!
Rusty Hinge!?! How do I keep my door hinges from rusting and creaking?! I had the same problem with my '93 (and I bought it new). I always keep the hinges lubed. Either with WD-40 or Slick 50 1-Lube (which I prefer). But, that just seems to be a temporary solution to the creaking. How do I remove the rust without ******* up the paint and solve this problem once and for all? 
Just soak it in amorall like you did the door panel.
Go to Lowes or Home Depot and get a can of Super Lube, it's a silver can.
It contains graphite and will stick to whatever you spray it on.
I use it on my garage door rollers and it lasts forever.
Go to Lowes or Home Depot and get a can of Super Lube, it's a silver can.
It contains graphite and will stick to whatever you spray it on.
I use it on my garage door rollers and it lasts forever.
Originally Posted by Charging TA
Maybe you need to rebuild the hinges? (Replace the pin)... Search around on Muscle Car/Classic car sites and you should find info on it.
Staging Lane
Joined: Jul 2005
Posts: 95
Likes: 1
From: Brighton, CO
No, you can get rid of the corrosion with a wire brush (corrosion brush). Pull apart the hinge (if you don't want to do that, then you won't fully get rid of the corrosion, and it will always come back!) You could just remove what you see by keeping the door attached, but if you wanted to remove the corrosion fully, remove the hinge. Then, take a wire brush to the dissambeled hinge. Scrub the **** out of it, remove the paint, and remove the corrosion. If it turned to pitting corrosion, then use a drill and a sanding disc to fully remove it. (smooth it out by using a higher grit and smooth it out) Then once complete, use a corrosion prevention compound (you can buy these at hardware stores, or checkers etc) and spray a few coats on the untreated hinge. Wait for it to dry, then paint the exterior. Spray a few coats of gloss black, then grease the hinge (I recommend Marina grease (it displaces water alot better)) Then reinstall the door and you're done.
Chances of a sagging door (if you choose to disassemble the hinge) are pretty high. So it's either keep doing corrosion work on your hinge, or chance a sagging door.
Chances of a sagging door (if you choose to disassemble the hinge) are pretty high. So it's either keep doing corrosion work on your hinge, or chance a sagging door.
Trending Topics
What about Naval Jelly? I've used that before on bike parts (chain, sprockets, chrome) but, never on a painted surface. I don't know how it would react and I don't want to **** up the paint in the door jamb. And, it's not a big enough deal to disassemble the door (not now anyway).
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Originally Posted by AnimalSS
What about Naval Jelly? I've used that before on bike parts (chain, sprockets, chrome) but, never on a painted surface. I don't know how it would react and I don't want to **** up the paint in the door jamb. And, it's not a big enough deal to disassemble the door (not now anyway).
Originally Posted by Scotty-Z
I would also reccomend the Litium Grease or just a ton of regular grease on it.
