3" double wall tips
3" double wall tips Hey guys im looking for 3" double wall tips just like the 3"duals firehawk#867* sells. I need some single 3" double wall, I want some exactly like those, so whos got them. Thanks guys.
Here ya go...they are 3.5", but close enough 
http://www.chromeandperformance.com/singletips.html
Bob S.
http://www.chromeandperformance.com/singletips.html
Bob S.
Trending Topics
thunderracing.com
They carry MEGS exhaust tips. I found some on the Megs site that I liked, and had Thunder order them and ship them to me.
I went with 4.5" rolled single slash cuts. They quality is great, much better than 95% of the stuff out there.
They carry MEGS exhaust tips. I found some on the Megs site that I liked, and had Thunder order them and ship them to me.
I went with 4.5" rolled single slash cuts. They quality is great, much better than 95% of the stuff out there.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Originally Posted by 01 Red WS6
why not get the reproduction tips that they sell to go in the cutlass bumper. I've seen them when i've been looking for parts for my 442
RADZ, check these out. I did all the work for you.
Pick the style, etc. on the left. This link is for the rolled edge singles and slash cuts. Pick your inlet, outlet, and overall length!
http://www.coneeng.com/megs/slick.htm
Write down the part # and order them from Thunder!
Rob
Pick the style, etc. on the left. This link is for the rolled edge singles and slash cuts. Pick your inlet, outlet, and overall length!
http://www.coneeng.com/megs/slick.htm
Write down the part # and order them from Thunder!
Rob
BAD *** TA WS6 ----- Do you have pics of yours? The angle they give im not really liking, Im not fond of that style but I think it might look good with the curves of the bumper. The reason Im being so picky, is that there are only 4 of these bumpers left on the market that are new, so im not going to order it unless I find the perfect tips. Once these 4 are gone, thats it, no more I have to buy used so I need to decide quick.
Originally Posted by radz
BAD *** TA WS6 ----- Do you have pics of yours? The angle they give im not really liking, Im not fond of that style but I think it might look good with the curves of the bumper. The reason Im being so picky, is that there are only 4 of these bumpers left on the market that are new, so im not going to order it unless I find the perfect tips. Once these 4 are gone, thats it, no more I have to buy used so I need to decide quick.
Are you looking for a side shot? I can get one tomorrow. The file attachment feature isn't allowing me to put them up anymore. I'm a 100kb over the limit.
EDIT: Nevermind I had them hosted on my pictures page under Randoms.
They look crooked, but my drivers side hanger is FUBAR. I'll get some decent side shots up tomorrow if you need them.
Rob
^^ that would be great BAD ***, do you think I could get a side shot, I would like to see the angle of the slach cut. Now that I see them on a vehicle I think those will look better than the corsa style.
Originally Posted by radz
Not really a fan of the trumpits, and the others listed above I didnt like, the SLP is nice but still a 3.5 and not a 3".
I can understand that, I've never been a fan of the trumpits either.
