Easiest way to wire up a transbrake button
Thread Starter
TECH Junkie
Joined: Jul 2015
Posts: 3,012
Likes: 48
Easiest way to wire up a transbrake button I'm falling on the sword here, when it comes to wiring I'm for the most part completely lost. Can someone explain the easiest way to go about this. This will be without a relay.
On your button you should have a small pigtail. Run trans brake wire to one of the leads off button, then run a 12v source to the other lead off of the button. When you press button it will then close the circuit and send 12v to ththe trans brake. I would probably use a ignition 12v source, ( switched )
You can run a relay and a master switch so you can only activate the t-brake when you want to. The wiring should go like this off the relay.
85-keyed hot 12V
86-to master switch then from master switch to ground.(this will turn on the relay to get the trans brake ready for use).
30-fused hot 12V (run a fuse off of 12v source)
87-to one wire of t-brake to your t-brake switch. The other wire off your 12v switch will go to ground.
Or you can run a fused 12v to one wire on your t-brake then your other wire off your t-brake to a master switch then to your t-brake switch. It depends on if you prefer to run a relay or not.
85-keyed hot 12V
86-to master switch then from master switch to ground.(this will turn on the relay to get the trans brake ready for use).
30-fused hot 12V (run a fuse off of 12v source)
87-to one wire of t-brake to your t-brake switch. The other wire off your 12v switch will go to ground.
Or you can run a fused 12v to one wire on your t-brake then your other wire off your t-brake to a master switch then to your t-brake switch. It depends on if you prefer to run a relay or not.
Thread Starter
TECH Junkie
Joined: Jul 2015
Posts: 3,012
Likes: 48
On your button you should have a small pigtail. Run trans brake wire to one of the leads off button, then run a 12v source to the other lead off of the button. When you press button it will then close the circuit and send 12v to ththe trans brake. I would probably use a ignition 12v source, ( switched )
TECH Regular
Joined: Dec 2014
Posts: 484
Likes: 18
From: Emory Texas currently
Trending Topics
On your button you should have a small pigtail. Run trans brake wire to one of the leads off button, then run a 12v source to the other lead off of the button. When you press button it will then close the circuit and send 12v to ththe trans brake. I would probably use a ignition 12v source, ( switched )
and don't forget to ground the solenoid as well
__________________
FTI COMPETITION CONVERTERS AND TRANSMISSIONS
"IT'S NOT CHEATING, IT'S THE COMPETITIVE EDGE."
1-866-726-8358
info@ftiperformance.com
FTIPerformance.com
FTI Converter build sheet
FTI COMPETITION CONVERTERS AND TRANSMISSIONS
"IT'S NOT CHEATING, IT'S THE COMPETITIVE EDGE."
1-866-726-8358
info@ftiperformance.com
FTIPerformance.com
FTI Converter build sheet
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo