BOSS APPROVED!
What kind of tranny cooler?
Thread Starter
On The Tree
Joined: Oct 2007
Posts: 102
Likes: 0
From: Scottsboro, AL
What kind of tranny cooler? I am fixing to put in my Yank SS3600 stall and 3.73 gears in this weekend and I don't know what brand or size or ANYTHING about what tranny cooler to go with... I need some sound advice!
It really simple the biggest you can fit and brand is not a big factor really IMO
__________________
Just get the biggest cooler your local auto store carries. I bought the biggest Hayden cooler that Autozone carried and installed it in front of my AC condenser. I also run a B&M 24K in-line, but my my converter is quite a bit bigger. You should be fine with a single cooler. Enoy that SS3600!!
I just bought a BMM-70274 cooler and BMM-80278 mounting kit and mounted up in front of my A/C condensor "radiator". I took out the plastic piece in there and it fits fine. This cooler has 1/2 pipe fittings , i wanted that so i could run a nice clean setup with braided hose. I have pics i can upload if you want more info. Id go with this one and dont worry about it. I have seen ppl run these without a fan and be just fine. I havent used mine yet im not worried.
Trending Topics
I ran both a Hayden 1404 AND a Hayden 1405 at the same time. A 1405 is too big in front of the radiator IMO, but it sure is nice to have one that big. I only pulled it off because I could mount it where the front bumper support used to be.
__________________
800-456-0211 / PM / Facebook
WHIPPLE Superchargers, Procharger, Magnuson, Powerbond Sale, HPTuners packages!, Trickflow, AFR, PRC, CHE Trunion upgrade, $100 7.400" pushrod set, Custom Cam of your choice
800-456-0211 / PM / Facebook
WHIPPLE Superchargers, Procharger, Magnuson, Powerbond Sale, HPTuners packages!, Trickflow, AFR, PRC, CHE Trunion upgrade, $100 7.400" pushrod set, Custom Cam of your choice
Last edited by Scoggin Dickey; Mar 13, 2008 at 10:20 AM.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
I just bought a BMM-70274 cooler and BMM-80278 mounting kit and mounted up in front of my A/C condensor "radiator". I took out the plastic piece in there and it fits fine. This cooler has 1/2 pipe fittings , i wanted that so i could run a nice clean setup with braided hose. I have pics i can upload if you want more info. Id go with this one and dont worry about it. I have seen ppl run these without a fan and be just fine. I havent used mine yet im not worried.
Im not quite sure I understand your question unless it means did i have to tap my own threads. No. Coolers comes with 1/2" female pipe threads. I bought fittings(1/2" male npt to 6an male) then fittings 6an female to 6an hose end(for the braided hose).
This is what i did for my new 4l80e, if you have stock hard lines runnining up there you may need different fittings.
I just wanted to run braided.
This is what i did for my new 4l80e, if you have stock hard lines runnining up there you may need different fittings.
I just wanted to run braided.
