Carb'ed & Cammed: low vacuum...
#1
Carb'ed & Cammed: low vacuum...
Hi All,
I'm starting to tune my newly running hybrid (LS powered Maverick) that has a Torquer V2 cam on a 113° LSA and Holley HP-82751 750 DP. I was having trouble getting it to idle under 1100. The carb was bought here slightly used but completely original. So far, I found the float levels were so low that the adjuster nuts were not even contacting the seat assembly and had to initially be unscrewed with needle nose pliers. Also, all 4 idle mix screws were only turned out 1/2 turn from full in.
After setting the float levels, it now idles great at 800 but is pig-rich and the idle mix screws do absolutely nothing. I hooked up a vacuum gauge and I'm seeing 7" at 800 RPM. Next, I'll try 3.5" power valves (I think it has 6.5"'s now), that should cure the idle mix richness.
Is that low a vacuum reading considered normal for this cam? It thumps pretty mean at 800, but technically, the cam is pretty small compared to other makes/styles of engines...
Russ
I'm starting to tune my newly running hybrid (LS powered Maverick) that has a Torquer V2 cam on a 113° LSA and Holley HP-82751 750 DP. I was having trouble getting it to idle under 1100. The carb was bought here slightly used but completely original. So far, I found the float levels were so low that the adjuster nuts were not even contacting the seat assembly and had to initially be unscrewed with needle nose pliers. Also, all 4 idle mix screws were only turned out 1/2 turn from full in.
After setting the float levels, it now idles great at 800 but is pig-rich and the idle mix screws do absolutely nothing. I hooked up a vacuum gauge and I'm seeing 7" at 800 RPM. Next, I'll try 3.5" power valves (I think it has 6.5"'s now), that should cure the idle mix richness.
Is that low a vacuum reading considered normal for this cam? It thumps pretty mean at 800, but technically, the cam is pretty small compared to other makes/styles of engines...
Russ
#4
TTT
Still looking for opinions and/or other's setups...
I'm "OK" with my idle, it just seems strange that all 4 idle screws are only 1/2 turn out instead of the recommended 1 1/2 turns. Someone on www.hotrodders.com said it's prolly due to this Holley series of carbs being designed for engines with a tighter LSA. It idles solid at 1000 pulling 10" vacuum. I've had it idling lower, but it's somewhat unsteady. I'll put my 4.5 PV back in and go for a drive!
Russ
Still looking for opinions and/or other's setups...
I'm "OK" with my idle, it just seems strange that all 4 idle screws are only 1/2 turn out instead of the recommended 1 1/2 turns. Someone on www.hotrodders.com said it's prolly due to this Holley series of carbs being designed for engines with a tighter LSA. It idles solid at 1000 pulling 10" vacuum. I've had it idling lower, but it's somewhat unsteady. I'll put my 4.5 PV back in and go for a drive!
Russ
#6
Thanks!
Russ
Trending Topics
#9
Russ
#10
TECH Addict
iTrader: (12)
236/236 .651/.651 110+4lsa, i saw -6.1 psia with the MSD, about 12.2HG. idle at 900 rpm, i could get it to idle at 600rpm but it shook my teeth out of my head.
with holley 750 vac secondary, 1.25 turns out, with demon 750 dp 3/4 turns out at 4 corner. i ran a 5.5 power valve and it worked fine. I'm a 6 speed though.
I ran 20 degrees timing at idle with 8 degrees advance at 900 rpm. so i had about 28 degrees at idle. it was smooth. I ran about 30 degrees WOT, 38 cruise.
with holley 750 vac secondary, 1.25 turns out, with demon 750 dp 3/4 turns out at 4 corner. i ran a 5.5 power valve and it worked fine. I'm a 6 speed though.
I ran 20 degrees timing at idle with 8 degrees advance at 900 rpm. so i had about 28 degrees at idle. it was smooth. I ran about 30 degrees WOT, 38 cruise.
#11
Teching In
Join Date: Nov 2008
Location: Atascadero, CA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
ever thought about trying one of these: http://www.summitracing.com/parts/CCA-5200/. big cams = low vacuum at idle. just a thought.
#12
I have a similar DP and have the same issue with the idle screws.
Mine isn't the HP, but the next model down mechanical secondary/4 corner idle screw DP. Mine doesn't have the replaceable air bleeds like the HP carbs do. My idle screws are 1/2 to 3/4 turn out.
the Holley book I have says some verisons of DP are set up for more radical cams, thus they build the idle circuits very rich. This book recommended bending a wire into a V and putting one into each idle jet.
I tried a small piece of wire but I don't think the wire was big enough. I have another, slightly larger wire I want to try next.
I am starting to think my solution will be a bigger cam to match the carb
Mine isn't the HP, but the next model down mechanical secondary/4 corner idle screw DP. Mine doesn't have the replaceable air bleeds like the HP carbs do. My idle screws are 1/2 to 3/4 turn out.
the Holley book I have says some verisons of DP are set up for more radical cams, thus they build the idle circuits very rich. This book recommended bending a wire into a V and putting one into each idle jet.
I tried a small piece of wire but I don't think the wire was big enough. I have another, slightly larger wire I want to try next.
I am starting to think my solution will be a bigger cam to match the carb
#13
236/236 .651/.651 110+4lsa, i saw -6.1 psia with the MSD, about 12.2HG. idle at 900 rpm, i could get it to idle at 600rpm but it shook my teeth out of my head.
with holley 750 vac secondary, 1.25 turns out, with demon 750 dp 3/4 turns out at 4 corner. i ran a 5.5 power valve and it worked fine. I'm a 6 speed though.
I ran 20 degrees timing at idle with 8 degrees advance at 900 rpm. so i had about 28 degrees at idle. it was smooth. I ran about 30 degrees WOT, 38 cruise.
with holley 750 vac secondary, 1.25 turns out, with demon 750 dp 3/4 turns out at 4 corner. i ran a 5.5 power valve and it worked fine. I'm a 6 speed though.
I ran 20 degrees timing at idle with 8 degrees advance at 900 rpm. so i had about 28 degrees at idle. it was smooth. I ran about 30 degrees WOT, 38 cruise.
ever thought about trying one of these: http://www.summitracing.com/parts/CCA-5200/. big cams = low vacuum at idle. just a thought.
I have a similar DP and have the same issue with the idle screws.
Mine isn't the HP, but the next model down mechanical secondary/4 corner idle screw DP. Mine doesn't have the replaceable air bleeds like the HP carbs do. My idle screws are 1/2 to 3/4 turn out.
the Holley book I have says some verisons of DP are set up for more radical cams, thus they build the idle circuits very rich. This book recommended bending a wire into a V and putting one into each idle jet.
I tried a small piece of wire but I don't think the wire was big enough. I have another, slightly larger wire I want to try next.
I am starting to think my solution will be a bigger cam to match the carb
Mine isn't the HP, but the next model down mechanical secondary/4 corner idle screw DP. Mine doesn't have the replaceable air bleeds like the HP carbs do. My idle screws are 1/2 to 3/4 turn out.
the Holley book I have says some verisons of DP are set up for more radical cams, thus they build the idle circuits very rich. This book recommended bending a wire into a V and putting one into each idle jet.
I tried a small piece of wire but I don't think the wire was big enough. I have another, slightly larger wire I want to try next.
I am starting to think my solution will be a bigger cam to match the carb
BIGGER, yeehaww!
Russ
#15
TECH Regular
iTrader: (12)
if im not mistaken i run 17* of timing from 0-1000 and then ramp my timing up to 29* at 3000 and sustain 29* until redline. Im running a six speed... but ive pulled it all the way to the red with no issues.
Im running a TSP magic stick 3 cam (237/242 .603/.609) and a 750 mighty demon carb. I have my air bleeds 1/2 - 3/4 out. its pretty rich at idle but i pull 10" or more at around 900.
I dont care about vacuum because i run hydroboost bakes. I am going to ditch the demon in favor of a holley hp street soon. the demon has some weird idle issues. its been to a carb professional and i still cant figure out why my idle rpm jumps up all crazy after a drive around the block. if i removed the return spring the idle increases like crazy. its almost like the base plate and butterflys are bent. ive had it.. its gotta go!
Im running a TSP magic stick 3 cam (237/242 .603/.609) and a 750 mighty demon carb. I have my air bleeds 1/2 - 3/4 out. its pretty rich at idle but i pull 10" or more at around 900.
I dont care about vacuum because i run hydroboost bakes. I am going to ditch the demon in favor of a holley hp street soon. the demon has some weird idle issues. its been to a carb professional and i still cant figure out why my idle rpm jumps up all crazy after a drive around the block. if i removed the return spring the idle increases like crazy. its almost like the base plate and butterflys are bent. ive had it.. its gotta go!