2004r - drive by wire? 
2004r - drive by wire?
Somebody on here has done it. Basicly what they did was mount the drive by wire pedal under the hood and then use a conventional throttle cable to pull the pedal and the TV cable as well. Also, hot rod recently did an article with like 9 crate engines in the same car some fuel injected and some not. They rigged up a gas pedal that was both electronic and cable so it would work with all the engines. Perhaps you could do this and just have the cable pull on the TV cable. This would be tricky but it could be made to work.
Thread Starter
Staging Lane
Joined: Mar 2008
Posts: 67
Likes: 0
From: NOR CAL
he stated constant pressure which is something new they came out with this year. It eliminates the tv cables hookup-pressure problem but you still have to have something to control your shift points. This has to be done mechanically and i cant figure out a 2004r hookup on ls series!
Well I used a mechanical linkage throttle body on my swap and hooked up the TV cable on my 700r4 with some custom bracketry. That may be the easiest way.
Last edited by pist0lpete; Nov 6, 2008 at 08:47 AM.
Trending Topics
you just run it back to your throttle pedal and rig a linkage..or as someone stated above, you use your mechanical throttle linkage to pull the drive by wire actuator(pedal) under the hood and connect the cable there.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
speed sensor I have the drive by wire as welll and was considering my options for using my 2004r.. But the cost of building a bullet proof version coupled with the rig required for tv cable and no speed sensor ( As I wanted a clean Cruise set-up) steered me away..
Scrap the 200 and go with a 4l60E. The pcm will then control everything and the finished product is a much better functioning and driving vehicle without any quirks. A LS swap is expensive and a lot of work. 4l60E's are a plenty these days and will work as designed without wasting a lot of time building something that may or may not work WELL.
Many would argue a 4l60 can't be built to be as strong as a 200r4. I would argue that for the money you could build a 4l80 and not have any doubts as to strength. However, I have no idea what kind of power Scotty here is making. I know with me I merely used the 700r4 because it was fairly strong and I already had it. When it blows I plan to do a T56 swap anyways.
Thread Starter
Staging Lane
Joined: Mar 2008
Posts: 67
Likes: 0
From: NOR CAL
ls 376/480. I have a built 2004r from previous classic car that I sold but kept the tranny. From what I understand I cant convert to a cable operated throttle body if I have a 58x reluctor!
he stated constant pressure which is something new they came out with this year. It eliminates the tv cables hookup-pressure problem but you still have to have something to control your shift points. This has to be done mechanically and i cant figure out a 2004r hookup on ls series!
http://store.summitracing.com/egnsea...115+4294904007
