Ls headers in a stock clip nova
Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
Ls headers in a stock clip nova For those interested in LS headers to fit the stock clip in a 62-67 Nova I will be taking a shop tour tomorrow 1-22-10 at a stainless header manufacture that is going to make headers exclusively for Church Boys Racing LLC.
What I would like to do is offer a "Group Buy" to anyone that would like to have one of the first sets available. These will be discounted for only the initial "Group Buy" after that they will be at full retail.
If you are interested please send me an Email or P/M. When I talk to them tomorrow I would like to give them an Idea of how many initial headers we will want, this will greatly dictate the initial cost/discount.
email to novasteering@aol.com
----note---- Photo is not an exact replica.
What I would like to do is offer a "Group Buy" to anyone that would like to have one of the first sets available. These will be discounted for only the initial "Group Buy" after that they will be at full retail.
If you are interested please send me an Email or P/M. When I talk to them tomorrow I would like to give them an Idea of how many initial headers we will want, this will greatly dictate the initial cost/discount.
email to novasteering@aol.com
----note---- Photo is not an exact replica.
Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
Primary size 1-3/4
collector 3"
band clamping system with "V" band upgrade option
O2 bungs will be in place
100% stainless
Motor mount/plate location is in the "Standard" position. The lower bolt hole for the motor mount shares the same hole as the lower front bolt hole on the mount plate.
Ground clearance is a must and will not hang lower than the transmission.
I have the Group Buy price send me a PM or call for the price.
collector 3"
band clamping system with "V" band upgrade option
O2 bungs will be in place
100% stainless
Motor mount/plate location is in the "Standard" position. The lower bolt hole for the motor mount shares the same hole as the lower front bolt hole on the mount plate.
Ground clearance is a must and will not hang lower than the transmission.
I have the Group Buy price send me a PM or call for the price.
Trending Topics
Are these the headers that wont clear the stock steering box and you have to add a $1800.00 rack and pinion conversion kit to your stock front end. 
I think I will stick to my Heidts front end.
I think I will stick to my Heidts front end. LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
Well Stainless Works are moving right along. Everything has been mocked up, and will soon be able to start bending the actual tubes for placement in the car.
Instead of making due with what they already have for tooling Stainless Works has purchased a special bending die for the tight bends that are required to fit this clip. It would have been easy to over look a small detail like that but, this just shows how in tune they are, with the quality of the finished product!
By the end of next week we could possibly have some photos of the headers in the car and bolted up.
Instead of making due with what they already have for tooling Stainless Works has purchased a special bending die for the tight bends that are required to fit this clip. It would have been easy to over look a small detail like that but, this just shows how in tune they are, with the quality of the finished product!
By the end of next week we could possibly have some photos of the headers in the car and bolted up.
Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
Photos Here is the next step in our header build up. By the middle of next week 3/2/10 I will be able to view the actual "finished" product and then it will be full steam ahead. If anyone who was interested in a set you need to contact me as we will need to finalize all the orders. clip guys take a good look.....
330-442-7162 or novasteering@aol.com
330-442-7162 or novasteering@aol.com
Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
When purchasing the CBR stainless headers by Stainless Works you will also get the proper motor mount plate needed to position the engine in the same place that we did while making these headers.
He may have a NorCal wagon already in the works
Aron,how far along are you?VooDooII has a 5.3 in the garage and a 700r for his Mint green wagon he bought the weekend of the SoCal BBQ.I have been looking for an LQ4 or LQ9 for my 67.So far all I have is lots of ideas and a set of CBR headers.
Aron,how far along are you?VooDooII has a 5.3 in the garage and a 700r for his Mint green wagon he bought the weekend of the SoCal BBQ.I have been looking for an LQ4 or LQ9 for my 67.So far all I have is lots of ideas and a set of CBR headers.
Registered User
Joined: Apr 2010
Posts: 13
Likes: 0
Thread Starter
Staging Lane
Joined: Oct 2009
Posts: 97
Likes: 0
From: ohio
A little update on what we have been working on. These will be a set of Stainless Shorty headers that will accommodate the Stock Steering in a 62-67 Nova as well as the rack/pinion equipped cars.
