C4 corvette - 5.3 "LSX" engine swap project [PICS]
#83
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
I've been slacking and not updating the forums that much. I have this thread going on a different corvette site so let me catch everyone up to where i'm at!
-------------------------------
Harness is done!
A few posts back I showed where the bolt that holds part of the brace that goes from the passenger side windshield to the frame extension was in the way when the header was installed. I removed this bolt and tack welded the bottom of the brace in place. There are still two more bolts on the top-side holding it on so this should be more than OK. Now my header clears!
Steam lines installed
New gaskets and foam installed
-------------------------------
Harness is done!
A few posts back I showed where the bolt that holds part of the brace that goes from the passenger side windshield to the frame extension was in the way when the header was installed. I removed this bolt and tack welded the bottom of the brace in place. There are still two more bolts on the top-side holding it on so this should be more than OK. Now my header clears!
Steam lines installed
New gaskets and foam installed
#84
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Time for some videos!
The first one is the result of us flooding the engine with fuel while trying to start it numerous times. Once the engine finally sparked it must have ignited that fuel and shot it out the exhaust ports. Also, there was no passenger side header installed at this time. No real damage was done, some burnt paint on the coil pack and black smoke on the plugs but that's really it.
http://www.youtube.com/watch?v=3We7Xls8AvY
And here she is finally running with open headers. I am very surprised at how smooth it ran, considering there's still a bunch of vacuum leaks, no O2 sensors hooked up and countless other things that still needs to be done. It was so loud it distorted the microphone a bit unfortunately.
http://www.youtube.com/watch?v=5FLmP4J0xFM
The first one is the result of us flooding the engine with fuel while trying to start it numerous times. Once the engine finally sparked it must have ignited that fuel and shot it out the exhaust ports. Also, there was no passenger side header installed at this time. No real damage was done, some burnt paint on the coil pack and black smoke on the plugs but that's really it.
http://www.youtube.com/watch?v=3We7Xls8AvY
And here she is finally running with open headers. I am very surprised at how smooth it ran, considering there's still a bunch of vacuum leaks, no O2 sensors hooked up and countless other things that still needs to be done. It was so loud it distorted the microphone a bit unfortunately.
http://www.youtube.com/watch?v=5FLmP4J0xFM
#85
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
MORE VIDEOS!!!
Hooked up a bunch of temporary vacuum lines (silicone lines coming tomorrow) and I have the oil pressure gauge working. Reading about 60 PSI during idle. She runs MUCH smoother now.
Enjoy the videos!
http://www.youtube.com/watch?v=0VjpYYqgz5M
http://www.youtube.com/watch?v=_seAOxwNUSw
Hooked up a bunch of temporary vacuum lines (silicone lines coming tomorrow) and I have the oil pressure gauge working. Reading about 60 PSI during idle. She runs MUCH smoother now.
Enjoy the videos!
http://www.youtube.com/watch?v=0VjpYYqgz5M
http://www.youtube.com/watch?v=_seAOxwNUSw
#86
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Ran into an issue. The bolt that holds the TV cable bracket to the trans snapped and it's not coming out. Had to drop the transmission in order to drill this bolt out. What a PITA! Anyway, the trans is back and I will post pictures as soon as I get my hard drive working on my computer....
Video of the first ride below!!!
http://www.youtube.com/watch?v=39oFjPUl4F4
Video of the first ride below!!!
http://www.youtube.com/watch?v=39oFjPUl4F4
#90
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Not sure why it's not catching right away. The cam position sensor is hooked up and the fuel pressure is steady at 57psi at the rails. Hopefully next weekend I will have more time to look into the issue. I will keep everyone updated.
Thanks for the comments!
Thanks for the comments!
#92
On The Tree
iTrader: (3)
Join Date: Jul 2010
Location: Orlando, FL
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
I had a 96 6 speed C4 and decided that puting a LS1 in it was pointless when I was beating C5's and LS1 fbodys continually and put down higher numbers stock for stock. But I eventally sold the C4 for a C5, then sold the C5 for my WS6, and soon I will sell the fbody for a C4 again. Hopefully ZR1 or LT4 car.
#96
i have an 1985 and i have a 2003 5.3 im gathering parts. i want to use my stock 700R4 trans as well. however my experience with 700s and tv geometry has been a hard lesson learned on my many 3rd gen f bodies. until i spoke with the tci folks and found the corrector linkage. that said thats my only fear with my swap. plz let me know
#98
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2010
Location: New York, Long Island
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
i have an 1985 and i have a 2003 5.3 im gathering parts. i want to use my stock 700R4 trans as well. however my experience with 700s and tv geometry has been a hard lesson learned on my many 3rd gen f bodies. until i spoke with the tci folks and found the corrector linkage. that said thats my only fear with my swap. plz let me know
Great people to work with and all their parts come with detailed instructions and phone support if needed. I'll try to post up some pictures of the TV cable adjustment once I recover all my images from my crashed hard drive