drift car kouki s14 / LS1 / G-force GSR
09-05-2011, 12:52 PM
#43
On The Tree
iTrader: (21)
Join Date: Jan 2008
Location: Moss Point, MS
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
That dual z32 brake setup is amazing. Didn't even know you could do that. Could you pm me some details on how that was done? I have an s14 that's getting a v8 too.
09-07-2011, 02:01 PM
#48
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
That tranny cost 4500$ vs the mount that is less then 100$
Thanks for your opinion ! It helped me made my decision
09-15-2011, 12:27 AM
#49
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
its geting there ... i just receved mydrive shaft from Drive shaft shop
3.5 inch alu monster
GForce roller 400 style output to R200 nissan rear put a 2-2-1309 rear flange , from seal o flat 49 3/4 in.
- hardened 32 spline TH400 , 4L80 1350 yoke 5.5"CC/TP
i started put back the fenders and body kit on the car !!!
3.5 inch alu monster
GForce roller 400 style output to R200 nissan rear put a 2-2-1309 rear flange , from seal o flat 49 3/4 in.
- hardened 32 spline TH400 , 4L80 1350 yoke 5.5"CC/TP
i started put back the fenders and body kit on the car !!!
09-18-2011, 01:02 PM
#50
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
i almost had to take my stock fuel tank out of the car and run a fuel safe in the back !!!!
the stock tank is incoparated to the tranny tunnel and its 5mm. away from hiting ... i had to cut out the stock bracket that hold's the hand-brake cable (where the heat shield is)
and here is a pic of my tranny tunnel that wehad to midified ... we need to built a top cover and its ready for wiring !!!
the stock tank is incoparated to the tranny tunnel and its 5mm. away from hiting ... i had to cut out the stock bracket that hold's the hand-brake cable (where the heat shield is)
and here is a pic of my tranny tunnel that wehad to midified ... we need to built a top cover and its ready for wiring !!!
09-18-2011, 07:43 PM
#52
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
10-01-2011, 10:48 PM
#54
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
i got some parts that were in the mail for more then a month ... men was i happy to see those things monday morning !!!
AIM MXL dash
C&R surge tank
...
surge tank instaled
but no time for my car .. i had to work on Dave Briggs s14 all week . i work for him and we are going to Irwindale for the FD pro-am allstars... the car leaves tonight for a 50hours trip accros the country and were flying on thursday
AIM MXL dash
C&R surge tank
...
surge tank instaled
but no time for my car .. i had to work on Dave Briggs s14 all week . i work for him and we are going to Irwindale for the FD pro-am allstars... the car leaves tonight for a 50hours trip accros the country and were flying on thursday
10-14-2011, 09:59 PM
#59
Teching In
Thread Starter
Join Date: Apr 2011
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
i got alot of things done to the car this week !!!
i redid the tranny mount ... cause it was solid mounted before ... i used the Sikky mount that was in my mount kit
finised up the tranny tunnel / paint and heat reflecting tape (fire wall and tranny tunnel)
im gonna mount the ECU under the dash where the tunnel connect to the firewall so i decided to put heat reflecting tape on the firewall and tranny tunnel (engin bay side)
i still need to trim the top plate that goes around the shifter ...
also before my trip to Cali ... i got in contact with Dan @ Part Shop Max for there Pro Drift Knuckle ... we got in contact at Irwindale had i bought them ... they have a 45mm rollcenter correction and 62 deg of steering angle
and since im talking about my FD trip here are some pics of the week-end ...
leaving MTL to Cali (6hours in a plane is long , when your use to work outside and always move)
here is Ryan Tuerck *RedBull Camaro*
Vaughn Gittin JR *Monster Mustang*
Team Falken pits
My Fav car out there Daijiro Yoshihara *Discount tire,Falken tire,SPD metalwork s13*
http://www.youtube.com/watch?v=pu0kFw-opwY&sns=fb
and the after party on the saturday got just abit out of hand ... to bad i didnt staid up to party with those guys all night i had to catch a plane at 8h00 the next day
the Hotel staff was freaking OUTTTTTTTTTTTTTTT
http://www.youtube.com/watch?v=c7htuWhON2g&sns=fb
i redid the tranny mount ... cause it was solid mounted before ... i used the Sikky mount that was in my mount kit
finised up the tranny tunnel / paint and heat reflecting tape (fire wall and tranny tunnel)
im gonna mount the ECU under the dash where the tunnel connect to the firewall so i decided to put heat reflecting tape on the firewall and tranny tunnel (engin bay side)
i still need to trim the top plate that goes around the shifter ...
also before my trip to Cali ... i got in contact with Dan @ Part Shop Max for there Pro Drift Knuckle ... we got in contact at Irwindale had i bought them ... they have a 45mm rollcenter correction and 62 deg of steering angle
and since im talking about my FD trip here are some pics of the week-end ...
leaving MTL to Cali (6hours in a plane is long , when your use to work outside and always move)
here is Ryan Tuerck *RedBull Camaro*
Vaughn Gittin JR *Monster Mustang*
Team Falken pits
My Fav car out there Daijiro Yoshihara *Discount tire,Falken tire,SPD metalwork s13*
http://www.youtube.com/watch?v=pu0kFw-opwY&sns=fb
and the after party on the saturday got just abit out of hand ... to bad i didnt staid up to party with those guys all night i had to catch a plane at 8h00 the next day
the Hotel staff was freaking OUTTTTTTTTTTTTTTT
http://www.youtube.com/watch?v=c7htuWhON2g&sns=fb
Last edited by Rbs14; 10-14-2011 at 10:26 PM.