5.3 in 96 impala
We've done a few of them. Give us a call at 732-691-6531. Are you sticking with the DBW or going DBC?
Jon
PSI
Jon
PSI
__________________
Your Source for LSX Conversion Parts!
www.psiconversion.com
Ebay Store
Facebook/psiconversion
Instagram/psiconversion
'Dont Let EFI Pass You By!'
Your Source for LSX Conversion Parts!
www.psiconversion.com
Ebay Store
Facebook/psiconversion
Instagram/psiconversion
'Dont Let EFI Pass You By!'
Trending Topics
You don't have to change the accessories to one that comes from a CAR with a 5.3, as the only ones that did was the newer Impala SS and its counterparts. You can use the truck accessories, they just need to be modified a little bit. I ran them that way for almost 3 years like that with nary a hiccup.
Not knocking you at all, but if you have to ask for a schematic for combining both wiring harnesses together, then maybe you should stick to the LT1, or pay someone to do the combining of the harnesses for you.
*rant*I've done everything on my swap myself, besides rebuilding the trans. The rear gears/differential, initial install, wiring, TC install, Cam install, Tuning (with some help from Ed Hutchins)were all done by me. The reason for this is because I had my harness reworked by a vendor on this site, and on the initial startup, it would idle at oh say 2500-3000rpm. He blamed me, and said I installed it wrong, so I pulled the harness apart, and instead of REMOVING the unneeded wires, they were stagger-cut and tucked back in the harness, pretty half assed for the ~800.00 I paid for his services. He will remain nameless as I'm not gonna start bashing him, but I was beyond pissed at the his services rendered. *end rant*
Anyway, what was the question?
Not knocking you at all, but if you have to ask for a schematic for combining both wiring harnesses together, then maybe you should stick to the LT1, or pay someone to do the combining of the harnesses for you.
*rant*I've done everything on my swap myself, besides rebuilding the trans. The rear gears/differential, initial install, wiring, TC install, Cam install, Tuning (with some help from Ed Hutchins)were all done by me. The reason for this is because I had my harness reworked by a vendor on this site, and on the initial startup, it would idle at oh say 2500-3000rpm. He blamed me, and said I installed it wrong, so I pulled the harness apart, and instead of REMOVING the unneeded wires, they were stagger-cut and tucked back in the harness, pretty half assed for the ~800.00 I paid for his services. He will remain nameless as I'm not gonna start bashing him, but I was beyond pissed at the his services rendered. *end rant*
Anyway, what was the question?
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Thread Starter
Registered User
Joined: May 2012
Posts: 3
Likes: 0
@GA95DCMSS i have no clue what exactly needs done!!! if i could get someone for example to say that i need such and such motor mounts, this oil pan, and what ac compressor bracket... then i would know if i was gone go through with it.
On The Tree
Joined: Mar 2011
Posts: 109
Likes: 0
From: Lakewood NJ
