93 Digicamo Rx7 'The Beater'
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
california, thanks!
Cleaning up that engine harness
discovered the injectors had to be lengthened
Mani was for a 92mm had to port it to run my 102, lolz aaron
map sensor mount
ait bung added, brake boost line and vac lines
throttle cable bracket
Started my dash sheet panel
interior fans!
mani all set, thoose are ford rails with custom tabs!
final assemble
trans cooler lines
modded t56 mount to hold up the 4l80e
started the oil cooler lines
just got to finish the fuel lines by the rails and we should have a first start on the turbo finalyl!
Cleaning up that engine harness
discovered the injectors had to be lengthened
Mani was for a 92mm had to port it to run my 102, lolz aaron
map sensor mount
ait bung added, brake boost line and vac lines
throttle cable bracket
Started my dash sheet panel
interior fans!
mani all set, thoose are ford rails with custom tabs!
final assemble
trans cooler lines
modded t56 mount to hold up the 4l80e
started the oil cooler lines
just got to finish the fuel lines by the rails and we should have a first start on the turbo finalyl!
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
got the driveshaft bits in
put the diffuser back on
modified and installed the rest of the exhaust
shes got a base tune now, hopefully winters sorts out with their shifter isn't working for me so we can test drive it and then go on the dyno finally for a tune.
from my buddy Wes, running vid
http://instagram.com/p/c5TQSaLtLz/
put the diffuser back on
modified and installed the rest of the exhaust
shes got a base tune now, hopefully winters sorts out with their shifter isn't working for me so we can test drive it and then go on the dyno finally for a tune.
from my buddy Wes, running vid
http://instagram.com/p/c5TQSaLtLz/
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
had to de-bur it a lot, make our own fuel rails, add a mount for the map and the ait otherwise its a cheap copy of the hogan manifold we like it a lot I got mine on fleabay talked the seller down to $500
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
85* Ambient
30.03 in-Hg Ambient
45% Humidity
Peak 717 WHP 627 Torque 14* Timing
It made its old peak by 4.8k lol
Big thanks to Jeremy Formato of Fasterproms
30.03 in-Hg Ambient
45% Humidity
Peak 717 WHP 627 Torque 14* Timing
It made its old peak by 4.8k lol
Big thanks to Jeremy Formato of Fasterproms
Last edited by Ruler_Mark; Sep 5, 2013 at 12:55 AM.
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
went to the track, after our 4th 140+ trap they told me I had to slow down or go home 
Was starting to hook real good too oh well time to get my nhra license. 1.9x 60 fts, should be at or around 10.0 and at or around 150 trap.
Was starting to hook real good too oh well time to get my nhra license. 1.9x 60 fts, should be at or around 10.0 and at or around 150 trap. LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
Whelp Jakes decided to give us a healthy discount and we now have an all billet 4l80e being built for us 
Since it will have a trans brake this was needed
Have a 3.08 gear sitting in a box for it aswell. Going to upgrade to walbro 485 dual pumps and bigger injectors e85 time
Hopefully get all this done before 2014 then save up for new wheels and shine burnout fenders.
Since it will have a trans brake this was needed
Have a 3.08 gear sitting in a box for it aswell. Going to upgrade to walbro 485 dual pumps and bigger injectors e85 time
Hopefully get all this done before 2014 then save up for new wheels and shine burnout fenders. 
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
Back together again, Big thanks to Jake @ Jake's performance. We were having some issues with the transmission they built for us and he personally came to our shop and resolved them. This new built trans feels alot better than the junkyard unit we were running before!
bigger trans cooler hole
Going to be @ OSW in Orlando fl this Saturday for Hot Import Nights we will be with Improved Racing at their booth, don't be shy come out and see us!
bigger trans cooler hole
Going to be @ OSW in Orlando fl this Saturday for Hot Import Nights we will be with Improved Racing at their booth, don't be shy come out and see us!
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
Stopped by Improved Racing today and Micheal hooked me up with a oil pan baffle and a crank scraper. Had to bust out the engine cradle to drop the sub frame to get the pan off.
Finished clearance-ing the crank scraper and snapped this pic before I put the windage tray on and buttoned her back up.
Thread Starter
Staging Lane
Joined: Sep 2009
Posts: 57
Likes: 1
Got a present in from bubbletech today..
Really nice piece Benny made
Test fit
Better shot of the canards
This was easier than anticipated and long overdue
finally building an air box for the filter..
Really nice piece Benny made
Test fit
Better shot of the canards
This was easier than anticipated and long overdue
finally building an air box for the filter..
