Finally, my own LS project!
Thread Starter
On The Tree
Joined: Nov 2007
Posts: 103
Likes: 0
Finally, my own LS project! When I bought it a month ago
As of yesterday
The car leaves for the chassis shop tomorrow. TCI front clip and a custom round tube moly chassis thoughout. The plan is a junk yard L59 swap with a S480 BW turbo. Hoping to make 600 with motor stock (but I need more education on this) with a CK performance Billet 200R4, a 315/60 drag radial and a 430 gear. Wish me luck.
As of yesterday
The car leaves for the chassis shop tomorrow. TCI front clip and a custom round tube moly chassis thoughout. The plan is a junk yard L59 swap with a S480 BW turbo. Hoping to make 600 with motor stock (but I need more education on this) with a CK performance Billet 200R4, a 315/60 drag radial and a 430 gear. Wish me luck.
Thread Starter
On The Tree
Joined: Nov 2007
Posts: 103
Likes: 0
Sadly, the car was clean, very clean.......er I mean solid! 
But, I hate rusty body work, so I searched for a while to find this one. No rust. Lots of dents and checked paint, but no rust. The floors needed to come out for the chassis work. I have asked the builder to follow the general shape/height of the original floor as best as he can. I will be keeping a back seat in it for my daughter, hence the reason I left that stich of panel to allow the builder to reference off of it. Hoping it will come in under 3000 lbs all in, and at 6oo +, it should move rather well.
But, I hate rusty body work, so I searched for a while to find this one. No rust. Lots of dents and checked paint, but no rust. The floors needed to come out for the chassis work. I have asked the builder to follow the general shape/height of the original floor as best as he can. I will be keeping a back seat in it for my daughter, hence the reason I left that stich of panel to allow the builder to reference off of it. Hoping it will come in under 3000 lbs all in, and at 6oo +, it should move rather well. Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Thread Starter
On The Tree
Joined: Nov 2007
Posts: 103
Likes: 0
Well, I had a hernia fixed and March break rolled around, so progress was a little slow, but we are moving again.
Chassis fab has begun...........
Rear housing just before back braces go on.
Beginnings of the moly round tube chassis ..
Chassis fab has begun...........
Rear housing just before back braces go on.
Beginnings of the moly round tube chassis ..
TECH Apprentice
Joined: Dec 2006
Posts: 311
Likes: 0
From: Marble Falls, TX
Thread Starter
On The Tree
Joined: Nov 2007
Posts: 103
Likes: 0
Well its been a long time since I posted. Haven't got as much as I'd like done as summer time is my busiest custom fab time of the year, and that's what finances my build, soooooo mine sits. Here's what I have gotten accomplished since my last post.
Unfortunately this is busy season, so I'm not sure when I'll get back at it. This Camaro is up in the air right now, and the tube chassis 34 is coming Saturday. It has a Camaro supercharged lsa, and 6 speed pulled from a wrecked 2013 Camaro.
[/
Unfortunately this is busy season, so I'm not sure when I'll get back at it. This Camaro is up in the air right now, and the tube chassis 34 is coming Saturday. It has a Camaro supercharged lsa, and 6 speed pulled from a wrecked 2013 Camaro.
[/