Conversion folks please list your conversion in here
#1701
#1702
Not converted yet. I just picked up a 2002 Camaro SS donor car to swap the LS1 and T56 into a 1969 Datsun Roadster. I look forward to getting some information but, being a new member, my posts are being limited.
#1703
LS-3 480/4L70E in my 61' Impala
Finally finished my LS-3 install and it runs and drives great.
I had a lot of inspiration from seeing what others have done on these forums.
Chevrolet Performance sells a great package and the 4L70E is programed with solid shifts. It chirps the tires on the 1-2 upshift on WOT and it fit my car without modification to the tunnel.
Combined with a 9" custom fabricated rear end and heavy duty driveshaft from Inland Empire driveline it all works together.
I hid the engine and transmission ECU's inside the car to keep the engine compartment clean.
Thanks to everyone here on LS1 Tech for the info you post.
Darrell Benner
Fremont CA.
I had a lot of inspiration from seeing what others have done on these forums.
Chevrolet Performance sells a great package and the 4L70E is programed with solid shifts. It chirps the tires on the 1-2 upshift on WOT and it fit my car without modification to the tunnel.
Combined with a 9" custom fabricated rear end and heavy duty driveshaft from Inland Empire driveline it all works together.
I hid the engine and transmission ECU's inside the car to keep the engine compartment clean.
Thanks to everyone here on LS1 Tech for the info you post.
Darrell Benner
Fremont CA.
#1704
72 chevelle LQ9
Finally finished my 72 chevelle after 2yrs.
LQ9 out of 2003 escalade
SRD custom camshaft
trunion upgrade
flowmaster headers
200 4r
2800 edge converter
4:10 12 bolt
Did 375 hp 400 tq on the dyno
LQ9 out of 2003 escalade
SRD custom camshaft
trunion upgrade
flowmaster headers
200 4r
2800 edge converter
4:10 12 bolt
Did 375 hp 400 tq on the dyno
#1706
Default Conversion folks please list your conversion in here
1967 Chevelle Malibu
New LSA/4L85E GM Connect & Cruise
Will post pics as I go including part numbers that work as there have been a few posts of some amazing builds but I'm still uncertain on part numbers for Accessory drives and AC mounts for the LSA in an a body..
Thanks, Jos
New LSA/4L85E GM Connect & Cruise
Will post pics as I go including part numbers that work as there have been a few posts of some amazing builds but I'm still uncertain on part numbers for Accessory drives and AC mounts for the LSA in an a body..
Thanks, Jos
Last edited by JosR; 12-19-2017 at 05:25 PM. Reason: add pics
#1707
I have a 1967 Pontiac GTO convertible with a 525 hp LS 3 hooked to a T56 magnum 6 speed Manual trans. Also For 9 inch with 3.89 gears. Used the Holley accessory drive brackets and Holley 302-2 oil pan. Have about 2000 miles on it and enjoying every mile! Got to figure out how to post pictures on this site.
#1710
#1711
Hello,
My conversion is using a model year 2000 Chevy Silverado LM7 VORTEC truck motor and its 4L60E transmission into my 1970 El Camino. Rust repairs have been my focus since acquiring this vehicle last April and she had been parked since about 1983-84 according to its last Texas inspection sticker and plate decal. All rust repairs have been finished and I'm hoping that next month will be a big month for the front brake disk conversion, coil overs, front suspension rebuild and the installation of the Dirty Dingo LS engine mounts.
I'm hoping that February will allow me to begin test fitting the motor and trans. Fingers crossed and hopeful.
Rick
My conversion is using a model year 2000 Chevy Silverado LM7 VORTEC truck motor and its 4L60E transmission into my 1970 El Camino. Rust repairs have been my focus since acquiring this vehicle last April and she had been parked since about 1983-84 according to its last Texas inspection sticker and plate decal. All rust repairs have been finished and I'm hoping that next month will be a big month for the front brake disk conversion, coil overs, front suspension rebuild and the installation of the Dirty Dingo LS engine mounts.
I'm hoping that February will allow me to begin test fitting the motor and trans. Fingers crossed and hopeful.
Rick
#1716
Pat
#1720
I honestly haven’t looked at the color of the sensor yet, but so far the resounding answer is 06 and up are all 58X. Just wanted to have the info on hand before I get started, ducks in a row if you will.