For you DIY 5.3 guys
For you DIY 5.3 guys I got tired of looking for a camaro or corvette accessory setup, so what i did was chop it up with out having to weld, so it can be usd on the A-body or what have you, no need for spending more money
ill have more pics up tommorow these are just some rough cuts..lol
ill have more pics up tommorow these are just some rough cuts..lol well for A-body (chevelles,Tempest...etc..) Truck acc brackets makes The alternator sit to damn high and the PS pump (saginaw style) hot the power steering gearbox, most of us have to convert to a F-body or corvette acc. mount setup to get around this problem what i did was chop it so the alternator dosent sit so high and the ps pump pulley will clear the PS gear box, if you have saw zaw and drill bit's this can be done in very little time.
the ALT wont hit come to find out but the PS pump cover where the pulley hits on the belt was ground down a little, and the PS bracket was slighlty drilled out so i could the clearnece i needed, I also made the truck manifolds work here some pics
and if anybody ever wondered about the truck mani's primaries and outlet they are 1.63 across and 1.59 up, the outlet specs at 2.25, Comparing the manifolds to the corvette ones, Truck manifolds actually have a bigger I.D primary and same size collector outlet, I will port the Exaust manifold slighlty after i reposition the 02 bung and other things.
Truck mani's.
Corvette mani's
Outer portion measured at 2.55, i couldnt hold the camera and keep my caliper inside but the inner "sleeve" is 2.25
and if anybody ever wondered about the truck mani's primaries and outlet they are 1.63 across and 1.59 up, the outlet specs at 2.25, Comparing the manifolds to the corvette ones, Truck manifolds actually have a bigger I.D primary and same size collector outlet, I will port the Exaust manifold slighlty after i reposition the 02 bung and other things.
Truck mani's.
Corvette mani's
Outer portion measured at 2.55, i couldnt hold the camera and keep my caliper inside but the inner "sleeve" is 2.25
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo I heard that somewhere to, but i tried anyway thats the main reason my bead is so thick though, had to make sure my weld penetrated, but im going to get some 2.5' pipe today and weld that instead of using the factory 2.25 piece as pictured. will post later on tonight or tommorow.
welded the 2.5 inch pipe in had to hammer the end to make it oval shape to "fit" the shape of the manifold but this should help it breathe alot better throughout the powerband and clear the frame rails with no problem...which is why i hacked them up in the first place lol...call me cheap
Last edited by 91parkave; Mar 17, 2008 at 02:37 PM.
