Done Broke
Thread Starter
11 Second Club
iTrader: (2)
Joined: Feb 2011
Posts: 3,729
Likes: 15
From: Fredonia,WI
Done Broke 
Sad face emoji
Only dragged this car about six times
New engine combo and this happened on my
Very first burnout last night
Second gear driving it out of the bleach box
With drag radials and no wheel hop
What should I expect to find broken and how
Much coin am I looking at ?????
Not unusual. Don't know the cost, or if the bracing systems available in the aftermarket would help. You might try the performance forum at the Corvette Forum. There will be some folks there who have been there and might have some good suggestions.
Don't know what rib you have. The 3 rib design from C5 Zo6 is supposed to be stronger than single rib.
corvette forums has a lot of info on these.
Also call RPM transmissions.
corvette forums has a lot of info on these.
Also call RPM transmissions.
Thread Starter
11 Second Club
iTrader: (2)
Joined: Feb 2011
Posts: 3,729
Likes: 15
From: Fredonia,WI
Yeah my trans was done by Jeremy and we've been in contact, will be sending him the broken junk in the next week here. Really considering going 3.90 polished gears for a bit more "giddy-up".
Thread Starter
11 Second Club
iTrader: (2)
Joined: Feb 2011
Posts: 3,729
Likes: 15
From: Fredonia,WI
Well just got off the phone with Jeremy a few hours ago and we decided to add the stronger ZO6 pinion support bearing to the stage two assembly. 300M outputs not needed for my power level, so the ZO6 stuff it is. Went 3.90 polished gears and got the external brace assembly too.
Apparently drag radials are just pure evil on Corvette rear end assemblies.
Might have to switch to bias plys or something with a softer sidewall.
Since my main case was also destroyed there is really nothing to even send him so outright w/core charge it is........OUCH......
Apparently drag radials are just pure evil on Corvette rear end assemblies.
Might have to switch to bias plys or something with a softer sidewall.
Since my main case was also destroyed there is really nothing to even send him so outright w/core charge it is........OUCH......
Trending Topics
Thread Starter
11 Second Club
iTrader: (2)
Joined: Feb 2011
Posts: 3,729
Likes: 15
From: Fredonia,WI
Jeremy set me up with another C5 piece....Apparently the C6 stuff requires additional conversion pieces to make it work....IDK
I'm getting like a hybrid stage 2/3 which will have upgraded ZO6 pinion support
as well as an external brace.....and polished 3.90s to help cure some of that
"sluggish" feeling.....
I'm getting like a hybrid stage 2/3 which will have upgraded ZO6 pinion support
as well as an external brace.....and polished 3.90s to help cure some of that
"sluggish" feeling.....
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Jeremy set me up with another C5 piece....Apparently the C6 stuff requires additional conversion pieces to make it work....IDK
I'm getting like a hybrid stage 2/3 which will have upgraded ZO6 pinion support
as well as an external brace.....and polished 3.90s to help cure some of that
"sluggish" feeling.....
I'm getting like a hybrid stage 2/3 which will have upgraded ZO6 pinion support
as well as an external brace.....and polished 3.90s to help cure some of that
"sluggish" feeling.....
Launching!
Joined: Apr 2005
Posts: 229
Likes: 3
From: Frisco TX
I looked into upgrading to the '07+ C6 diff (I think that's the correct year the diff housing changed) with 3.90s when I had my C5. IIRC, there's additional pieces needed to plant the updated C6 diff into a C5 but it's fairly straight forward. If the C5 external brace is at least just as strong and offsets the cost and extra labor involved with the conversion, that's the way to go I would think.
Thread Starter
11 Second Club
iTrader: (2)
Joined: Feb 2011
Posts: 3,729
Likes: 15
From: Fredonia,WI
Quick update.......have yet to track the car but the "butt-cheek dyno" reports that it is faster.....imagine that....?????
freeway rpms sit right at 2000 for eighty miles per hour and fuel economy hovers right around 24....dropping it to seventy brings 26 and sixty mph gets me the original GM rating of 28 mpgs....I'll take that all day
Runs real well no ticks, leaks, nothing....just get in it and drive wherever kinda deal......VERY happy with the trans/rear-end from RPM/Jeremy !!!!
freeway rpms sit right at 2000 for eighty miles per hour and fuel economy hovers right around 24....dropping it to seventy brings 26 and sixty mph gets me the original GM rating of 28 mpgs....I'll take that all day
Runs real well no ticks, leaks, nothing....just get in it and drive wherever kinda deal......VERY happy with the trans/rear-end from RPM/Jeremy !!!!