Need some HELP!!!
Need some HELP!!! I was down at the track (Cecil County Dragway) this past Saturday and run a new best of 11.58@120 with a 1.69 60FT, before that the runs were ranging from 11.7-11.9's. My new best was with my tires PSI at 12PSI and my 2 step at 5K, and my Eibach Drag bag at 10PSI. Almost every launch I did that day had a huge BANG on the launch, but I was still cutting 1.7 60ft too. Here's a basic setup of my suspansion.
MWC Fab 9" TQ arm pinion angle set at -2
Comp rear shocks set at 50/50
Eibach prokit drag launch springs and air bag set at 10psi
shock front shocks
Aftermarket panhard bar and control arms
I'm triing to figure out what would cause this bang, wheather its the new comp shocks which is the only suspansion part I changed for this season, I've read that people are pretty happy with 50/50 on these supposedly. I'm also running a spec twin which grabs like hell but it was in last year and didn't make anything bang like this......also could it just be a by product from using the 2 step now, considering my foot is to the floor as opposed to just hoving at an RPM and human error on launches (slow gas pedal down, slow clutch pedal up).
Vid Added....
http://www.youtube.com/watch?v=sePvnSDqir4
http://www.youtube.com/watch?v=2V1MHuTLjq8
MWC Fab 9" TQ arm pinion angle set at -2
Comp rear shocks set at 50/50
Eibach prokit drag launch springs and air bag set at 10psi
shock front shocks
Aftermarket panhard bar and control arms
I'm triing to figure out what would cause this bang, wheather its the new comp shocks which is the only suspansion part I changed for this season, I've read that people are pretty happy with 50/50 on these supposedly. I'm also running a spec twin which grabs like hell but it was in last year and didn't make anything bang like this......also could it just be a by product from using the 2 step now, considering my foot is to the floor as opposed to just hoving at an RPM and human error on launches (slow gas pedal down, slow clutch pedal up).
Vid Added....
http://www.youtube.com/watch?v=sePvnSDqir4
http://www.youtube.com/watch?v=2V1MHuTLjq8
Last edited by DiabloFormula; Mar 22, 2010 at 10:36 PM.
Tranny mount torn? Motor mounts shot? Exhaust hitting the rear? Rear hitting the floorboards? Ujoints in the driveshaft getting loose? Bolts loose somewhere? I'd look at those things first, I'd suspect that one of those is probably causing the problem.
Added another vid....at .40 you can see a slow motion launch from the rear, which shows my pass side tire spinning and my drivers side hitting hard and you can also see the rear and pretty much everything under the rear of the car shaking, any guesses, I'm still running a stock rear sway bar and I know this perticular day my air bag was at 15 PSI.
Needs more air in the bag or a real sway bar on it. It squats hard on the right rear and moves right. Also make sure the rear is centered in the car and front to back, make sure everything is tight and go from there.
Thats what i got from your vid.
Thats what i got from your vid.
Trending Topics
i would vote for a rear sway/drag bar set-up from like BMR/Spohn, etc. That will plant your tires evenly. Also, adjustable front shocks and lower control arms relocation brackets.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
great to see you got a pb, but there are a few things the car needs. Front shocks and a sway bar for sure... I have an adjustable tube chromemoly anti-roll bar that bolts to the Midwest fab rearend. call me and I'll get ya taken care of.
not sure about the bang but i'd look for contact somewhere... top of torque arm over rearend maybe? if no then maybe exhaust pop from the two-step? wouldn't be a bad idea to check the driveshaft slip yoke for twisted splines also... M6 cars are hard on them.
not sure about the bang but i'd look for contact somewhere... top of torque arm over rearend maybe? if no then maybe exhaust pop from the two-step? wouldn't be a bad idea to check the driveshaft slip yoke for twisted splines also... M6 cars are hard on them.
