Top 10 camonly vidoes
http://precisionracecomponents.com/1051Cam.MOV
Here's a decent video of the BRP from back in '05 I think. It went a 10.51 with a MS3 cam in it. I think it was the cam only record for about a week before someone went faster with a T-rex or something like that. Those were the days! Seemed like everyone was going back and forth trying to be the fastest cam only and heads/cam cars.
Jon
Here's a decent video of the BRP from back in '05 I think. It went a 10.51 with a MS3 cam in it. I think it was the cam only record for about a week before someone went faster with a T-rex or something like that. Those were the days! Seemed like everyone was going back and forth trying to be the fastest cam only and heads/cam cars.
Jon
I am sure Rodney went faster than this video but all of the old links to videos are now broken. I found this one linked from the customer cars section on Thunder Racing's site.http://www.youtube.com/watch?v=ye5OH...layer_embedded
Last edited by 5.3LJimmy; Feb 15, 2011 at 01:50 PM.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Thread Starter
TECH Senior Member
iTrader: (28)
Joined: Nov 2005
Posts: 5,556
Likes: 6
From: Rochester, NY
http://www.youtube.com/watch?v=98GhFY0lml0
2 and 3mins my shitbox
I think I remember watching some other vids, on the LS1tech video site. Thats been gone for years. Anyone have any on there hardrives get them on youtube or somthing.
2 and 3mins my shitbox
I think I remember watching some other vids, on the LS1tech video site. Thats been gone for years. Anyone have any on there hardrives get them on youtube or somthing.
Thread Starter
TECH Senior Member
iTrader: (28)
Joined: Nov 2005
Posts: 5,556
Likes: 6
From: Rochester, NY
Magnus and jugger had the best cam only and h/c/i car's in are area back int the day.
Here is vid of my junk going 10.88 at 127 pig heavy. and at the same track as the vids of magnus ride
http://s275.photobucket.com/albums/j...ueSScamaro.mp4
Here is vid of my junk going 10.88 at 127 pig heavy. and at the same track as the vids of magnus ride
http://s275.photobucket.com/albums/j...ueSScamaro.mp4
And I will be sending you pic's soon of all the weight that came out of my ride so far. Motor is out and almost ready for fly cutting and front end is stripped done to nothing 
sawzall and plasma are getting a work out 
Probably not top 10 but here's my 10sec 6spd camonly junk. Min 1.40 and 4.40. http://www.youtube.com/watch?v=YbYi2Prtk1M
Thread Starter
TECH Senior Member
iTrader: (28)
Joined: Nov 2005
Posts: 5,556
Likes: 6
From: Rochester, NY
check my siq
ya thouse 2 10.66 was open headers, it makes more power with the Ypipe BTW. I didn't have a way to hold it up, just took it off the night before quick. It was running 10.80s the week before with the 2OTL diriving it to the track. Then ran it open headers for 2 track visits. It was really consistent, like 10.661 10.665 day of that vid. And a few days before for 10.705? a 10.700 and a 10.669 or something really close like that. I posted about that with the slips and vids in the results section if you want more info.
Best setup would be a lightwight alum merg Yipe, or maybe a Xpipe then dumps like promod1955 built on his SI setup. My Y pipe is mild steel 3 into 4 one piece down the middle so its heavy, and has no hanger or anything.
ya thouse 2 10.66 was open headers, it makes more power with the Ypipe BTW. I didn't have a way to hold it up, just took it off the night before quick. It was running 10.80s the week before with the 2OTL diriving it to the track. Then ran it open headers for 2 track visits. It was really consistent, like 10.661 10.665 day of that vid. And a few days before for 10.705? a 10.700 and a 10.669 or something really close like that. I posted about that with the slips and vids in the results section if you want more info.
Best setup would be a lightwight alum merg Yipe, or maybe a Xpipe then dumps like promod1955 built on his SI setup. My Y pipe is mild steel 3 into 4 one piece down the middle so its heavy, and has no hanger or anything.
check my siq
ya thouse 2 10.66 was open headers, it makes more power with the Ypipe BTW. I didn't have a way to hold it up, just took it off the night before quick. It was running 10.80s the week before with the 2OTL diriving it to the track. Then ran it open headers for 2 track visits. It was really consistent, like 10.661 10.665 day of that vid. And a few days before for 10.705? a 10.700 and a 10.669 or something really close like that. I posted about that with the slips and vids in the results section if you want more info.
Best setup would be a lightwight alum merg Yipe, or maybe a Xpipe then dumps like promod1955 built on his SI setup. My Y pipe is mild steel 3 into 4 one piece down the middle so its heavy, and has no hanger or anything.
ya thouse 2 10.66 was open headers, it makes more power with the Ypipe BTW. I didn't have a way to hold it up, just took it off the night before quick. It was running 10.80s the week before with the 2OTL diriving it to the track. Then ran it open headers for 2 track visits. It was really consistent, like 10.661 10.665 day of that vid. And a few days before for 10.705? a 10.700 and a 10.669 or something really close like that. I posted about that with the slips and vids in the results section if you want more info.
Best setup would be a lightwight alum merg Yipe, or maybe a Xpipe then dumps like promod1955 built on his SI setup. My Y pipe is mild steel 3 into 4 one piece down the middle so its heavy, and has no hanger or anything.
Weld a stiff hanger in like I had speed inc do to mine...
Uses the passenger side body mount trq arm holes...
Thread Starter
TECH Senior Member
iTrader: (28)
Joined: Nov 2005
Posts: 5,556
Likes: 6
From: Rochester, NY
ya. I never spent time to make anything up. I want to make all alum tubing going to the muffler. My friend has 3inch with a alum vibrant muffler and form the turbo to back bumper it was something like 7pounds. But I would have it quieter with my 2OTL, or a hooker areo chamber, or some case muffler.