Roll Cage Jegs Or Summit Any Feedback
Thread Starter
9 Second Club
iTrader: (34)
Joined: Mar 2005
Posts: 2,248
Likes: 0
From: SPRINGFIELD MISSOURI
Roll Cage Jegs Or Summit Any Feedback Just wanted to know if anyone has used these pre bent cages and do they work ok. Im just looking for a 6 pt to get me by at the track. I still use my car daily but run low mid 10s. I have a local shops that builds there own and powder coats them. but the guy is looking to get around $700.00. THanks
Originally Posted by dnkynrbk
Just wanted to know if anyone has used these pre bent cages and do they work ok. Im just looking for a 6 pt to get me by at the track. I still use my car daily but run low mid 10s. I have a local shops that builds there own and powder coats them. but the guy is looking to get around $700.00. THanks
My buddy tried one for his foxbody and it fit andlooked like ****.
A buddy tried a Jegs one. They don't fit well. There real heavy. I wouldn't save the money there. Stenod has a real good deal on theres.
Originally Posted by dnkynrbk
Just wanted to know if anyone has used these pre bent cages and do they work ok. Im just looking for a 6 pt to get me by at the track. I still use my car daily but run low mid 10s. I have a local shops that builds there own and powder coats them. but the guy is looking to get around $700.00. THanks
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Chris alston's chassisworks also makes a nice cage that goes around the dash for LT1/LS1 cages.... prebent, notched, and fits very well.... here's a pic of mine.... I think all the bars ran me like 400 bucks.....
speaking of the coating on the bars I had heard that before about nothing other than paint... well check this out: yesterday i went to look at a car whom my engine builder is building a motor for.... this guy had done his WHOLE cage in yellow bed liner coating (yes that gritty looking spray on crap to keep from killing your truck bed)..... i'm not lying... craziest thing i ever seen....
speaking of the coating on the bars I had heard that before about nothing other than paint... well check this out: yesterday i went to look at a car whom my engine builder is building a motor for.... this guy had done his WHOLE cage in yellow bed liner coating (yes that gritty looking spray on crap to keep from killing your truck bed)..... i'm not lying... craziest thing i ever seen....
95 check your PM's...
My cage is a full cage good down to 8.50.... a rollbar will be good down to 10.0 which is generally like a 6 point...
mine is a 12 point... with the optional rocker bars at the bottom...
My cage is a full cage good down to 8.50.... a rollbar will be good down to 10.0 which is generally like a 6 point...
mine is a 12 point... with the optional rocker bars at the bottom...
I did a jegster 8pt myself, obviously for 150 bucks dont expect it to fit like a glove. the main hoop in my kit was actualy for a monte carlo, i had to trim it down. from there every bar is "intentionly" made too long to cut to your needs. the hardest part for me was cutting the notches back in when i trimed my peices and getting the angles cut to fit the body or floor right.. if you mess that up your running a good chance your bar will be too short after correcting you angle cuts it. All around if your fairly good with your hands i say its worth the time and effort. it was my first cage i was happy in the end. Deff dont rush it!!! it took alot of time to do all the measuring to assure i still had a perfectly original full leather working interior with carpet!! if you do a jegster youll need a pile of cutting and grinding wheels!!!
be careful though if you need it in 2 weeks. i ordered one and it took several weeks,
be careful though if you need it in 2 weeks. i ordered one and it took several weeks,
Last edited by smokin2002; Feb 16, 2007 at 05:23 PM.
