Dynamometer Results & Comparisons Dyno Records | Dyno Discussion | Dyno Wars

Patrick G Custom Cam only Mustang Dyno Numbers Installed & Tuned by EPP

Thread Tools
 
Search this Thread
 
Old 01-07-2008, 04:35 PM
  #1  
11 Second Club
Thread Starter
iTrader: (16)
 
2000SS1979's Avatar
 
Join Date: May 2006
Location: Plymouth, Indiana
Posts: 561
Likes: 0
Received 1 Like on 1 Post

Default Patrick G Custom Cam only Mustang Dyno Numbers Installed & Tuned by EPP

I had my custom cam installed by the guys over at EPP. They are great guys to deal with and fantastic customer service from Jake and Bob.

Also a big thanks for Patrick designing this cam for me!

I called over to the shop today to set up a time to pick my car up tomorrow and Jake said he had finished tuning my car and it put down 399RWHP and 372TQ. They cam is basically a 224/230 113+2. I was super impressed with the numbers. This was through a TSP Catted "y" also. Tomorrow when I pick up the car I will post up the dyno sheet for you guys. I will also take video of it after I pick the car up for you guys tomorrow!

The car is going to be a lot of fun after I install my 100 shot this spring.

Thanks again to EPP they are a great sponsor and know their stuff. Here is a link to their webpage Exotic Performance Plus

Current mods are in my sig.
ADDED VIDEO LINK OF CAM IDLE

Dyno Results 399RWHP @ 6220 RPM 373TQ @ 4800RPM I actually hit 400RWHP at 6400RPM but then it goes back down.

Last edited by 2000SS1979; 01-10-2008 at 08:37 AM. Reason: adding link & picture
Old 01-07-2008, 05:18 PM
  #2  
TECH Fanatic
iTrader: (1)
 
66deuce's Avatar
 
Join Date: Feb 2004
Location: Goshen,In.
Posts: 1,027
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by 2000SS1979
I had my custom cam installed by the guys over at EPP. They are great guys to deal with and fantastic customer service from Jake and Bob.

Also a big thanks for Patrick designing this cam for me!

I called over to the shop today to set up a time to pick my car up tomorrow and Jake said he had finished tuning my car and it put down 399RWHP and 372TQ. They cam is basically a 224/230 113+2. I was super impressed with the numbers. This was through a TSP Catted "y" also. Tomorrow when I pick up the car I will post up the dyno sheet for you guys. I will also take video of it after I pick the car up for you guys tomorrow!

The car is going to be a lot of fun after I install my 100 shot this spring.

Thanks again to EPP they are a great sponsor and know their stuff. Here is a link to their webpage Exotic Performance Plus

Current mods are in my sig.
good numbers..congrats!

Last edited by 66deuce; 01-07-2008 at 06:38 PM.
Old 01-07-2008, 05:20 PM
  #3  
11 Second Club
Thread Starter
iTrader: (16)
 
2000SS1979's Avatar
 
Join Date: May 2006
Location: Plymouth, Indiana
Posts: 561
Likes: 0
Received 1 Like on 1 Post

Default

It has a Professional Products 85MM intake & Throttle Body.
Old 01-07-2008, 05:20 PM
  #4  
TECH Junkie
 
1989GTA's Avatar
 
Join Date: Dec 2005
Posts: 3,092
Likes: 0
Received 5 Likes on 5 Posts

Default

..and it was on a Mustang dyno. Yes good numbers.
Old 01-07-2008, 05:54 PM
  #5  
11 Second Club
iTrader: (13)
 
venom ws7's Avatar
 
Join Date: Jul 2003
Location: EARTH
Posts: 5,965
Likes: 0
Received 1 Like on 1 Post

Default

Congrats man great numbers on Mustang Dyno.

Patrick Like always good job and EPP Always have great customer service.
Old 01-07-2008, 06:01 PM
  #6  
TECH Regular
iTrader: (19)
 
02 z/28's Avatar
 
Join Date: Feb 2006
Posts: 493
Likes: 0
Received 0 Likes on 0 Posts

Default

nice numbers.
Old 01-07-2008, 06:15 PM
  #7  
TECH Veteran
iTrader: (10)
 
BayAreaSS's Avatar
 
Join Date: May 2006
Location: Bay Area, CA (Pittsburg)
Posts: 4,240
Likes: 0
Received 2 Likes on 2 Posts

Default

Those are REALLY good numbers on a mustang dyno for that size cam
Old 01-07-2008, 06:17 PM
  #8  
12 Second Club
iTrader: (17)
 
Nimitz87's Avatar
 
Join Date: Dec 2004
Location: Cooper City, FL
Posts: 1,449
Likes: 0
Received 0 Likes on 0 Posts

Default

this is sad....great results from you however it makes me depressed looking at my heads/cam/intake car making 11 more hp.

Chad
Old 01-07-2008, 06:57 PM
  #9  
11 Second Club
Thread Starter
iTrader: (16)
 
2000SS1979's Avatar
 
Join Date: May 2006
Location: Plymouth, Indiana
Posts: 561
Likes: 0
Received 1 Like on 1 Post

Default

Thanks a lot everyone.. I was really excited when Jake told me today. I think this also puts to rest the myth that the Professional Product intake sucks at making power.
Old 01-07-2008, 07:06 PM
  #10  
9 Second Club
iTrader: (33)
 
GrimReaper's Avatar
 
Join Date: Nov 2003
Location: Lafayette Indiana
Posts: 372
Likes: 0
Received 0 Likes on 0 Posts

Default

nice numbers, and EEP is a very good group of guys to work with.
Old 01-07-2008, 07:08 PM
  #11  
TECH Fanatic
iTrader: (1)
 
66deuce's Avatar
 
Join Date: Feb 2004
Location: Goshen,In.
Posts: 1,027
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by 2000SS1979
Thanks a lot everyone.. I was really excited when Jake told me today.
good to see some local guys on here post up...
Old 01-07-2008, 07:19 PM
  #12  
LS1 Tech Administrator
iTrader: (14)
 
Patrick G's Avatar
 
Join Date: Nov 2001
Location: Victoria, TX
Posts: 8,245
Likes: 0
Received 32 Likes on 28 Posts

Default

Nice numbers. Look forward to seeing the curves. I have the same exact cam in my car. It's a sweetheart...especially if you plan on boosting the motor down the road.
__________________

2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.

Old 01-07-2008, 07:22 PM
  #13  
Shorty Director
iTrader: (1)
 
VINCE's Avatar
 
Join Date: Nov 2001
Location: Valrico, Florida
Posts: 8,260
Received 4 Likes on 3 Posts

Default

Great #'s!!!
Old 01-08-2008, 12:52 AM
  #14  
TECH Fanatic
iTrader: (7)
 
GMmexican's Avatar
 
Join Date: Jan 2006
Location: San Jose, CA
Posts: 1,607
Likes: 0
Received 0 Likes on 0 Posts
Default

great numbers.......i cant wait to order my pat g speced cam
Old 01-08-2008, 03:47 AM
  #15  
TECH Addict
iTrader: (6)
 
GreenBlood's Avatar
 
Join Date: Aug 2006
Location: Schiller Park (NW burb of Chicago)
Posts: 2,310
Likes: 0
Received 0 Likes on 0 Posts
Default

sick numbers man...
Old 01-08-2008, 04:59 PM
  #16  
11 Second Club
Thread Starter
iTrader: (16)
 
2000SS1979's Avatar
 
Join Date: May 2006
Location: Plymouth, Indiana
Posts: 561
Likes: 0
Received 1 Like on 1 Post

Default

Here is a link to my cam idle >>>>>CLICK ME<<<<< I know my car is dirty as hell. But it rained all day and I drove it home from EPP. I think it sounds awsome. Tomorrow I will get some revs for you guys also. I accidentally left my dyno sheet at work. But I will scan it in at work and upload it for your review tomorrow at work.
Old 01-08-2008, 05:24 PM
  #17  
JPH
TECH Junkie
iTrader: (2)
 
JPH's Avatar
 
Join Date: Jan 2006
Location: Fort Wayne, IN
Posts: 3,776
Likes: 0
Received 0 Likes on 0 Posts

Default

Originally Posted by Patrick G
Nice numbers. Look forward to seeing the curves. I have the same exact cam in my car. It's a sweetheart...especially if you plan on boosting the motor down the road.
How many different cams have you had in your car patrick? That thing probably needs a new set of cam bearings by now!
Old 01-08-2008, 05:35 PM
  #18  
LS1 Tech Administrator
iTrader: (14)
 
Patrick G's Avatar
 
Join Date: Nov 2001
Location: Victoria, TX
Posts: 8,245
Likes: 0
Received 32 Likes on 28 Posts

Default

Originally Posted by JPH
How many different cams have you had in your car patrick? That thing probably needs a new set of cam bearings by now!
That would probably be true if this was the original engine in my TA. The one in it now is my low compression turbo motor. It was built by Erik Koenig and only has 2k miles on it. Cam bearings are shiny and new.

PS, it's for sale too, wink wink.
__________________

2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.

Old 01-08-2008, 07:56 PM
  #19  
FormerVendor
 
Brent@LPE's Avatar
 
Join Date: Aug 2005
Location: Decatur IN.
Posts: 531
Likes: 0
Received 0 Likes on 0 Posts
Default

Great Stuff !!! i am sure we Will See you back soon! You have a sweet car and it was a pleasure to work on. Give me a call on Thurs. I want to make sure everything is A O.K.
Old 01-09-2008, 12:20 AM
  #20  
11 Second Club
iTrader: (8)
 
green28's Avatar
 
Join Date: Jul 2005
Location: NW IN
Posts: 1,730
Likes: 0
Received 0 Likes on 0 Posts

Default

Nice numbers! But you know, that just means I'm gonna need even more car lengths now! Maybe if it ever quits raining and the floods back off you can take it out and have some fun on dry pavement.


Quick Reply: Patrick G Custom Cam only Mustang Dyno Numbers Installed & Tuned by EPP



All times are GMT -5. The time now is 07:14 PM.