!wire mod
Originally Posted by deanasdork
Anyone in Orlando done this? I am thinking about doing it and wanted some help if anyone has done it before.
I did it.
It took WAYYY longer than expected because my damn hole saw broke. I spend so much time trying to fix it but ended up just going to Home Depot and buying one.
So just make sure you have a nice strong hole saw, a fully charged drill, and you'll be set.
It took WAYYY longer than expected because my damn hole saw broke. I spend so much time trying to fix it but ended up just going to Home Depot and buying one.
So just make sure you have a nice strong hole saw, a fully charged drill, and you'll be set.
Trending Topics
its a nice appearance mod. just make sure you use a decent bi-metal saw, find a gromment to fit the size hole you cut and tape the wires really good. i found it to be well worth the time.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
Not much involved if you plan it right. I cut a rectangular hole big enough for the wire harness to squeeze thru and ran the wires under the fender, sandwitched between the plastic fender liner. No extending/cutting of the wires. I used a drill bit without a hole saw. 4 holes with the drill bit and then a jig saw to cut the rectangle.
Originally Posted by camaroextra
Whether its worth it or not is totally subjective.
Mike, car looks good. When are you putting in your LTs?
TECH Fanatic
Joined: Jan 2005
Posts: 1,162
Likes: 0
From: St. Augustine, FL
I did this. Its a piece of cake. I didn't use any grommet for the hole I cut, I just filed it down enough to where there wasn't a sharp/jagged edge and also protected the wires with the plastic piping. here's photos:
The Before
The After
Various others
http://i131.photobucket.com/albums/p...e/PICT2962.jpg
http://i131.photobucket.com/albums/p...e/PICT2963.jpg
http://i131.photobucket.com/albums/p...e/PICT2994.jpg
http://i131.photobucket.com/albums/p...e/PICT2997.jpg
http://i131.photobucket.com/albums/p...e/PICT3002.jpg
The Before
The After
Various others
http://i131.photobucket.com/albums/p...e/PICT2962.jpg
http://i131.photobucket.com/albums/p...e/PICT2963.jpg
http://i131.photobucket.com/albums/p...e/PICT2994.jpg
http://i131.photobucket.com/albums/p...e/PICT2997.jpg
http://i131.photobucket.com/albums/p...e/PICT3002.jpg
Originally Posted by FBodyPerformer
Mike, car looks good. When are you putting in your LTs?
Pics were taken when I did my hood swap about 2 months ago. LTs and Duals have been on there for 2 weeks.. its MEAN. Trying to decide on a good tune now.
Originally Posted by FBodyPerformer
Hence the "?" at the end dick
Mike, car looks good. When are you putting in your LTs?
Mike, car looks good. When are you putting in your LTs?
Originally Posted by 92slowmaro
hey FBodyPerformer, speaking of LTs when are you putting yours on..... oh wait you gave them to your ex-girlfriend.