63 Nova X275 Build 410" LSX 88mm
#22
The main area of interference is the passenger side where the trans cooler lines go into the trans, you could make it fit without cutting out thee whole tunnel but it was just easier that way for me. I cut around the tunnel about 1" off the floor and used that 1" to create a flange to attach the new taller tunnel to. I also made a new trans crossmember and incorporated a driveshaft loop in as well while the tunnel was out. I will post pics tomorrow.
Last edited by 68 SS; 02-26-2012 at 08:42 PM.
#24
Thanks Bob, glad you found my new thread! The car is a much better platform than the camaro was for what I want to do with it, and the fact that it is rust free sealed the deal for me. The paint is far from perfect but the plan is to get it together and sorted out this summer then blow it back apart for a repaint this coming winter.
Trans tunnel mods are complete new trans crossmember and driveshaft loop are in just need to finish a few odds and ends then install the motor and trans for the final time then I will start the wiring and plumbing...I am way more than ready to hear it run!
Trans tunnel mods are complete new trans crossmember and driveshaft loop are in just need to finish a few odds and ends then install the motor and trans for the final time then I will start the wiring and plumbing...I am way more than ready to hear it run!
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
#25
I have been busy got the trans tunnel, crossmember and driveshaft loop all finished then stuck the trans in it for what I hope is the final time this afternoon. Time to start wiring as much as I hate to!
#27
No regrets here, I am 6'6" and can easily get in and out with the bars behind the dash. As much trouble as it is to go through the dash you will only gain 3" of clearance not really worth the trouble.
#29
installed the headers they are Schoenfeld 1 3/4 stepped to 1 7/8 and really suck they did not fit well at all but I made them work for now, I will be building my own 2" primary headers at a later date. I also discovered I will have to add two more u-joints to my steering shaft...it never ends LOL.
Got all the sound mat in and started the wiring this morning so it will be a few days for anymore updates still waiting on my new fuel cell the pump is mounted so hopefully the cell will show up so after the wiring I can attack the fuel system plumbing.
I sold the F1R I had and was planing on going F2 but after looking at the F1X specs I believe it will be the best option so I am going to give the new blower a try.
Got all the sound mat in and started the wiring this morning so it will be a few days for anymore updates still waiting on my new fuel cell the pump is mounted so hopefully the cell will show up so after the wiring I can attack the fuel system plumbing.
I sold the F1R I had and was planing on going F2 but after looking at the F1X specs I believe it will be the best option so I am going to give the new blower a try.
#30
Not much to add today just more wiring and installing electrical components hope to get this knocked out by Monday. Only got half a day in on the car today due to the storms coming through our area hope everyone out there is safe!
#31
installed the headers they are Schoenfeld 1 3/4 stepped to 1 7/8 and really suck they did not fit well at all but I made them work for now, I will be building my own 2" primary headers at a later date. I also discovered I will have to add two more u-joints to my steering shaft...it never ends LOL.
Got all the sound mat in and started the wiring this morning so it will be a few days for anymore updates still waiting on my new fuel cell the pump is mounted so hopefully the cell will show up so after the wiring I can attack the fuel system plumbing.
I sold the F1R I had and was planing on going F2 but after looking at the F1X specs I believe it will be the best option so I am going to give the new blower a try.
Got all the sound mat in and started the wiring this morning so it will be a few days for anymore updates still waiting on my new fuel cell the pump is mounted so hopefully the cell will show up so after the wiring I can attack the fuel system plumbing.
I sold the F1R I had and was planing on going F2 but after looking at the F1X specs I believe it will be the best option so I am going to give the new blower a try.
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
#32
Still plugging away at the wiring and getting everything into the car and mounted hope to finish up this week with the majority of the wiring. Still waiting on my fuel cell the intercooler water tank should be here today.
#33
#34
Did I mention how much I hate wiring??? Still wiring missed a few days due to hanging out with the family (they come first you know) but have the gauge cluster wired and ready to go in and the gauge panel that goes in the radio hole too. All of the electrical components are in the car and mounted and all the wire is pulled to the correct location working on terminating everything now and this car has a bunch of wires!
Still waiting on a fuel cell apparently it is on backorder from JAZ should be ready to fire this coming weekend.
Still waiting on a fuel cell apparently it is on backorder from JAZ should be ready to fire this coming weekend.
#35
It will be interesting to see how it runs for you! Bob
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
#36
I have about 90% of the wiring complete going to working on finishing it up tomorrow.
UPS brought me more parts today got my FAST dual wide band with the RPM sensor. Anyone else using the FAST wide band and how do you like it? I plan on wiring it into HP Tuners for the logging capability.
I finally found the fuel cell I needed Atlantic Speed in MD had it in stock got it on the way hopefully it will get here before Saturday if it does I can fire it off for the first time.
UPS brought me more parts today got my FAST dual wide band with the RPM sensor. Anyone else using the FAST wide band and how do you like it? I plan on wiring it into HP Tuners for the logging capability.
I finally found the fuel cell I needed Atlantic Speed in MD had it in stock got it on the way hopefully it will get here before Saturday if it does I can fire it off for the first time.
#37
Starting to look like a car again, got all the gauges and dash wiring completed still need to do a little tidying up under the dash and zip tie a few wires up but it a is all terminated. Got the fuel cell yesterday and the fittings I needed to convert it to -10 feed going to get working on the fuel system today hopefully I will have a start up video tomorrow.
#38
Got a lot done this weekend finished up all of the wiring and am I glad that is over! Got the intake on and all the engine harness plugged in and ran the -10 feed and -8 return lines then realized I goofed up and bought the wrong size AN fittings for the fuel rails so no start up yet but really close. Hope to get a little done this week but will have to slow down as I start work again tomorrow after 14 months of vacation.
#39
Love this car. What did you use for motor mount plates and what kit did you buy for the trans tunnel? A kit from a chassis builder maybe? Thanks a lot. Can't wait to hear this thing.
#40
The trans tunnel kit I bought from chassis engineering in Vero beach FL.
I can't wait to hear it either with any luck I will fire it up tomorrow afternoon!
Thanks for the kind Comments!