***3/11/13 UPDATE*** Project Xtreme Boost! '02 Xtreme Blazer, Single Turbo 5.3
#1
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
***3/11/13 UPDATE*** Project Xtreme Boost! '02 Xtreme Blazer, Single Turbo 5.3
Well the past few months I have been debating on either building a pretty much full race twin or single turbo s10 or a stout little street truck. I recently finished a 5.3 Swap in a 01 S10 for a friend so I am VERY familiar with what fits and what doesn't, LOL.
Here's what I have decided on, a 2002 Xtreme Blazer. I really wanted the extra seating so the whole family could go cruising to car shows or whatever together. I buddy of mine happen to be selling his 2002 Xtreme, 102k miles on the clock, clean as a whistle, runs perfect.
Here is a run down of all the parts I am using and what my goals are.
This will be a fully capable daily driver that retains A/C and all creature comforts. Stock appearance outside. I'll be tuning myself using HPTuners, SD tune. Stock 5.3 wiring harness will be mated to stock harness so all factory gauges will work as if it came from GM this way.
I am building the turbo kit in my garage from the Turbo headers to the charge piping. This will give you guys on the fence about building your own turbo kit that it is fairly easy to build without a bunch of special high end crap. Battery will be relocated to the back to make room for the turbo. This will be a front mounted turbo. Drivers side header log will be forward facing, hugged close against the block, below the timing cover, under the right front frame rail then up thru the factory battery location. Pass header will be routed forward facing, right above the heater hoses on water pump, snaked around and mated to drivers side into a T4 flange to turbo. Downpipe will be 3", routed below the coolant resevoir on the pass side, above the upper control arm then routed down the pass frame rail dumped by the pass rear tire. Cold side will be 3" Stainless strait from the turbo to throttle body, no intercooler for now as I only plan on running 9-12psi.
My budget it $5000 total which includes the purchase of the Blazer (I got a great deal on it).
Below if the basic crap I have so far...
2005 5.3 83k Miles $550
2003 PCM and Wiring Harness (Cable Driven) $100
HPTuners $500
Stock 4L60E (For now to get it running, then going TH400) $0
Stock LS1 Intake Manifold $0
Stock Thottle Body $0
Used 60lb Injectors $250
Used Hummer H3 Pan $100
Trans Dapt Engine Mount Kit $75
Used 224 Cam (115) $200
Used Comp 918's $75
Used HD Pushrods $60
Stock Fuel Pump with addition to In-Line Walbro 255 $109
ON 3 76mm Turbo $360
EMUSA 38mm Wastegate $75
EMUSA 50mm B/O $65
T4 Flange $17
Oil Feed Line to Turbo ($50)
Oil Drain Tube and Fitting ($30)
1/2" LS1 Header Flanges (2" Primary) $60
(4) 2" Mild Steel U-Bends $50
Misc 2.5" and 3" Mild Steel U, J, and Strait Pipes ($120)
Misc 3" Stainless Steel Bends ($75)
Stock Radiator $0
Dual Low Profile Fans with Aluminum Shroud $150
TRG Plugs and New Wires ($80)
Synthetic Oil and Filter ($35)
Prob some other stuff I am missing, I'll update it as I remember.
Plenty of pics showing step by step progress. Will keep this updated requently. Plan on driving it within a month. I am super excited about this build and think its gonna be a ton of fun to cruise around!
Stock as can be!
Unloading 5.3
Pulling the V6
H3 Pan
5.3 All Cleaned Up
Getting it ready to drop in
Mounts Used, fit like a glove!
5.3 Resting in place!
Sure looks good in there
Here's what I have decided on, a 2002 Xtreme Blazer. I really wanted the extra seating so the whole family could go cruising to car shows or whatever together. I buddy of mine happen to be selling his 2002 Xtreme, 102k miles on the clock, clean as a whistle, runs perfect.
Here is a run down of all the parts I am using and what my goals are.
This will be a fully capable daily driver that retains A/C and all creature comforts. Stock appearance outside. I'll be tuning myself using HPTuners, SD tune. Stock 5.3 wiring harness will be mated to stock harness so all factory gauges will work as if it came from GM this way.
I am building the turbo kit in my garage from the Turbo headers to the charge piping. This will give you guys on the fence about building your own turbo kit that it is fairly easy to build without a bunch of special high end crap. Battery will be relocated to the back to make room for the turbo. This will be a front mounted turbo. Drivers side header log will be forward facing, hugged close against the block, below the timing cover, under the right front frame rail then up thru the factory battery location. Pass header will be routed forward facing, right above the heater hoses on water pump, snaked around and mated to drivers side into a T4 flange to turbo. Downpipe will be 3", routed below the coolant resevoir on the pass side, above the upper control arm then routed down the pass frame rail dumped by the pass rear tire. Cold side will be 3" Stainless strait from the turbo to throttle body, no intercooler for now as I only plan on running 9-12psi.
My budget it $5000 total which includes the purchase of the Blazer (I got a great deal on it).
Below if the basic crap I have so far...
2005 5.3 83k Miles $550
2003 PCM and Wiring Harness (Cable Driven) $100
HPTuners $500
Stock 4L60E (For now to get it running, then going TH400) $0
Stock LS1 Intake Manifold $0
Stock Thottle Body $0
Used 60lb Injectors $250
Used Hummer H3 Pan $100
Trans Dapt Engine Mount Kit $75
Used 224 Cam (115) $200
Used Comp 918's $75
Used HD Pushrods $60
Stock Fuel Pump with addition to In-Line Walbro 255 $109
ON 3 76mm Turbo $360
EMUSA 38mm Wastegate $75
EMUSA 50mm B/O $65
T4 Flange $17
Oil Feed Line to Turbo ($50)
Oil Drain Tube and Fitting ($30)
1/2" LS1 Header Flanges (2" Primary) $60
(4) 2" Mild Steel U-Bends $50
Misc 2.5" and 3" Mild Steel U, J, and Strait Pipes ($120)
Misc 3" Stainless Steel Bends ($75)
Stock Radiator $0
Dual Low Profile Fans with Aluminum Shroud $150
TRG Plugs and New Wires ($80)
Synthetic Oil and Filter ($35)
Prob some other stuff I am missing, I'll update it as I remember.
Plenty of pics showing step by step progress. Will keep this updated requently. Plan on driving it within a month. I am super excited about this build and think its gonna be a ton of fun to cruise around!
Stock as can be!
Unloading 5.3
Pulling the V6
H3 Pan
5.3 All Cleaned Up
Getting it ready to drop in
Mounts Used, fit like a glove!
5.3 Resting in place!
Sure looks good in there
Last edited by Vcious04; 03-11-2013 at 09:32 PM. Reason: update
#3
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Drivers Side Tacked Together
Drivers Side Fully Welded
Not the greatest, I'm a little rusty but it will do, lol
Drivers Side in Place and Coated
Another Shot
Perfect clearance betweem power steerng pump and motor mount. Steering shaft clears with NO modification.
Pass side comming together, 2" Primarys on a 2.5" Log
Another shot
Pass side fully welded
Another shot
Gotta pat myself on the back, that looks plain SICK!
#4
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
I'll keep posting progress with tons of pics! I am going to try to get into a magazine with this build with some kind of topic as, "See what $5k Can do for You!". I dunno, it would be cool tho
Tomarrow I will slap the motor back in and fab up the hot side.
TO BE CONTINUED!!
Tomarrow I will slap the motor back in and fab up the hot side.
TO BE CONTINUED!!
#6
TECH Regular
iTrader: (2)
Join Date: Dec 2009
Location: Austin Texas
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
This it going to be bada$$!!!
I have been wanting an Extreme for a long time, just have never found the right deal at the right time.
I have a brand new 5" (I think) fiberglass hood hanging in my garage for that year model s10 truck. I did a 1992 S10 drag truck w/ sbc, tubbed, ect, about 6 years ago. I ordered a cowl hood for it and they sent the wrong one so I just ordered another one and kept thi one just in case...
If your interested in it let me know Im in Austin- I might trade you something for it...
I have been wanting an Extreme for a long time, just have never found the right deal at the right time.
I have a brand new 5" (I think) fiberglass hood hanging in my garage for that year model s10 truck. I did a 1992 S10 drag truck w/ sbc, tubbed, ect, about 6 years ago. I ordered a cowl hood for it and they sent the wrong one so I just ordered another one and kept thi one just in case...
If your interested in it let me know Im in Austin- I might trade you something for it...
Trending Topics
#8
http://img.photobucket.com/albums/v3...t/IMG_2034.jpg
why not notch the primary piping so it's not blocking half the flow inside the log pipe
why not notch the primary piping so it's not blocking half the flow inside the log pipe
#11
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I know Dan, would make it more nice that's for sure. I almost pulled the trigger on that Eastwood tig 200 combo with the plasma cutter and cart for $1299. I really dont weld enough I guess to justify it lol.
#13
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Well I got quite a bit accomplished this weekend working on it a few hours or so. Main goal this weekend was getting the turbo mounted. I did have to make a few changes tho....
Drivers side header I made had to be "massaged" on the #5 and #7 area where steering shaft goes. Once I removed everything I will re-design that a bit so it flows well. Also removed the coolant resevoir and trimmed the inner metal fender tub on the pass side to make room for the turbo and downpipe. Nothing major as I will weld the liner back in once the downpipe is completed so everything fits great without a ton of water flying in the engine bay as I will be driving this everywhere, lol.
What I did get accomplished was the hot side at about 90%. Pass side is fully welded, V-Band in place and all. Drivers side is all tacked together, ran out of time today but will be merging the drivers side to the pass side tomarrow.
Anyways I think it looks completely BADASS and couldn't be more happy with the way things are going. Pics honestly do not do justice, need to see in person to kinda take it all in.
Here's some more eye candy!! Sorry for the dark pics on some of them, flash is jacked up on my camera.
Whats do you guys think so far?
Drivers side header I made had to be "massaged" on the #5 and #7 area where steering shaft goes. Once I removed everything I will re-design that a bit so it flows well. Also removed the coolant resevoir and trimmed the inner metal fender tub on the pass side to make room for the turbo and downpipe. Nothing major as I will weld the liner back in once the downpipe is completed so everything fits great without a ton of water flying in the engine bay as I will be driving this everywhere, lol.
What I did get accomplished was the hot side at about 90%. Pass side is fully welded, V-Band in place and all. Drivers side is all tacked together, ran out of time today but will be merging the drivers side to the pass side tomarrow.
Anyways I think it looks completely BADASS and couldn't be more happy with the way things are going. Pics honestly do not do justice, need to see in person to kinda take it all in.
Here's some more eye candy!! Sorry for the dark pics on some of them, flash is jacked up on my camera.
Whats do you guys think so far?