6.0 + S480 = 1289 rear wheel horsepower.
02-20-2013, 03:49 PM
#24
02-20-2013, 04:54 PM
#28
This is very very good news! awesome results.
id also like some engine specs. pm to me if youd like!
id also like some engine specs. pm to me if youd like!
__________________
YOUR SOURCE FOR ALL THINGS TURBO!
CASEY@HURONSPEED.COM
Check us out on Facebook at: www.facebook.com/HuronSpeed
TWITTER @HURONSPEED
YOUR SOURCE FOR ALL THINGS TURBO!
CASEY@HURONSPEED.COM
Check us out on Facebook at: www.facebook.com/HuronSpeed
TWITTER @HURONSPEED
02-20-2013, 11:01 PM
#35
Guys... im not trying to be a killjoy but this particular test was setup to be a ***** to the wall gates pinned shut comparison. I doubt equal boost level testing will happen with this particular car... its a race car... it needs every single hp it can muster.
We have units going on other motors to do street car style dyno's. X psi pulls etc etc. It will take a little time for those numbers to materialize.... so please bear with us. I promise Ill share info with the couple of units im involved with directly and any information Jose passes along.
Backpressure was getting stupid... just like we figured it would. At the point this compressor is at...i felt the 6.0 would be too many cubes for the 96 wheel and thats pretty much what happened. Even with the 1.58 A/R i will be hard pressed to reccomend it on anything bigger than a 5.3 if its a big effort build.... if its milder effort... itll work Ok on the bigger inches....but i will be adjusting how i cam it.
Ideally.... i think we can make more power than this motor made with a 5.3 or a 4.8.
I fully believe Jose has come up with an 80mm wheel that will move 150 lb min.
We have units going on other motors to do street car style dyno's. X psi pulls etc etc. It will take a little time for those numbers to materialize.... so please bear with us. I promise Ill share info with the couple of units im involved with directly and any information Jose passes along.
Backpressure was getting stupid... just like we figured it would. At the point this compressor is at...i felt the 6.0 would be too many cubes for the 96 wheel and thats pretty much what happened. Even with the 1.58 A/R i will be hard pressed to reccomend it on anything bigger than a 5.3 if its a big effort build.... if its milder effort... itll work Ok on the bigger inches....but i will be adjusting how i cam it.
Ideally.... i think we can make more power than this motor made with a 5.3 or a 4.8.
I fully believe Jose has come up with an 80mm wheel that will move 150 lb min.
02-20-2013, 11:19 PM
#37
Guys... im not trying to be a killjoy but this particular test was setup to be a ***** to the wall gates pinned shut comparison. I doubt equal boost level testing will happen with this particular car... its a race car... it needs every single hp it can muster.
We have units going on other motors to do street car style dyno's. X psi pulls etc etc. It will take a little time for those numbers to materialize.... so please bear with us. I promise Ill share info with the couple of units im involved with directly and any information Jose passes along.
Backpressure was getting stupid... just like we figured it would. At the point this compressor is at...i felt the 6.0 would be too many cubes for the 96 wheel and thats pretty much what happened. Even with the 1.58 A/R i will be hard pressed to reccomend it on anything bigger than a 5.3 if its a big effort build.... if its milder effort... itll work Ok on the bigger inches....but i will be adjusting how i cam it.
Ideally.... i think we can make more power than this motor made with a 5.3 or a 4.8.
I fully believe Jose has come up with an 80mm wheel that will move 150 lb min.
We have units going on other motors to do street car style dyno's. X psi pulls etc etc. It will take a little time for those numbers to materialize.... so please bear with us. I promise Ill share info with the couple of units im involved with directly and any information Jose passes along.
Backpressure was getting stupid... just like we figured it would. At the point this compressor is at...i felt the 6.0 would be too many cubes for the 96 wheel and thats pretty much what happened. Even with the 1.58 A/R i will be hard pressed to reccomend it on anything bigger than a 5.3 if its a big effort build.... if its milder effort... itll work Ok on the bigger inches....but i will be adjusting how i cam it.
Ideally.... i think we can make more power than this motor made with a 5.3 or a 4.8.
I fully believe Jose has come up with an 80mm wheel that will move 150 lb min.
