02 TA Procharged
I have the inter cooler mounted and and all driver side piping installed. I will be mounting the head unit today as well as the passenger side piping. Think it would be ok to go ahead and install the Racetronix hotwire and pump with out tune? I have 60lb injectors but I wont put those in until I get to the tuner. I could prolly finish today but I am still waiting on my Super damper to come in the mail.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
what dyno will it be on.
what is your compression ratio.
what cubes.
what is your pulley size
crank pulley size.
automatic or 6 speed
10 bolt or 9 inch
what size cam.
running any methanol?
start there and can get you in the ballpark.
allout made 571 on 5.5 psi
i made 600 on 9psi.
alchemist made 750+ on 16 with a boost leak and conservative timing.
we were all d1. but that p1 should get you to 550 to 600 easily. enough to max out that single racetronix here soon.
what is your compression ratio.
what cubes.
what is your pulley size
crank pulley size.
automatic or 6 speed
10 bolt or 9 inch
what size cam.
running any methanol?
start there and can get you in the ballpark.
allout made 571 on 5.5 psi
i made 600 on 9psi.
alchemist made 750+ on 16 with a boost leak and conservative timing.
we were all d1. but that p1 should get you to 550 to 600 easily. enough to max out that single racetronix here soon.
what dyno will it be on.
what is your compression ratio.
what cubes.
what is your pulley size
crank pulley size.
automatic or 6 speed
10 bolt or 9 inch
what size cam.
running any methanol?
start there and can get you in the ballpark.
allout made 571 on 5.5 psi
i made 600 on 9psi.
alchemist made 750+ on 16 with a boost leak and conservative timing.
we were all d1. but that p1 should get you to 550 to 600 easily. enough to max out that single racetronix here soon.
what is your compression ratio.
what cubes.
what is your pulley size
crank pulley size.
automatic or 6 speed
10 bolt or 9 inch
what size cam.
running any methanol?
start there and can get you in the ballpark.
allout made 571 on 5.5 psi
i made 600 on 9psi.
alchemist made 750+ on 16 with a boost leak and conservative timing.
we were all d1. but that p1 should get you to 550 to 600 easily. enough to max out that single racetronix here soon.
10.5/1 compression
347 ci
6 speed
10 bolt
228/230 cam
no meth
my buddy had almost that exact setup and he made 550/570ish(I dont remember the exact torque) out of his p1, then he sold it and went turbo lol. Like everyone else said they are a ton of fun on the street!
Are you still in Hawaii? Unless things have changed in the last 4 months (Just moved from there after 4 years) there weren't any E85 stations and 10.5:1 is not going to allow you to run too much boost on Hawaii gas.
Is that the Hobby Shop on Schofield?
Is that the Hobby Shop on Schofield?
Yes still in Hawaii. Been here since 2008. I leave in couple months for the main land. That Hobby shop i was at is the one on MCBH. I dont plan on any more than like 8psi. When i get to where im going to turn it up a bit.
Did the balancer show up yet? Bob
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website