BAP, which one? MDS or KB?
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
Originally Posted by 30th t/a
which model KB BAP are you guys using...the 30amp or the 40amp.
also, where did you purchase the BAP at?
also, where did you purchase the BAP at?
I'd look at the caspers thing Ed, I never tried one but if MM says it works its a much easier and cheaper solution. You wont hurt anything in the car with a couple extra volts for the short WOT time. I'm even thinking of trying one just to give the ignition itself a little boost at WOT.
TECH Apprentice
Joined: Jan 2004
Posts: 337
Likes: 0
From: Frisco TX (Dallas Area)
Here's one the W-body guys use - probably the same as the others. I think it's a little cheaper though. "Flocharger"
http://www.zzperformance.com/grand_p...ts1.php?id=405
HTH
http://www.zzperformance.com/grand_p...ts1.php?id=405
HTH
Here's the link to the Caspers one.
https://www.casperselectronics.com/M.../merchant.mvc?
Nice price and if MM say's it works, I'm sure it does.
https://www.casperselectronics.com/M.../merchant.mvc?
Nice price and if MM say's it works, I'm sure it does.
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
I ordered one.
Originally Posted by Richiec77
Here's the link to the Caspers one.
https://www.casperselectronics.com/M.../merchant.mvc?
Nice price and if MM say's it works, I'm sure it does.
https://www.casperselectronics.com/M.../merchant.mvc?
Nice price and if MM say's it works, I'm sure it does.
Originally Posted by Ed Blown Vert
I ordered one.
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
I decided to put my old tune back in, before I was having problems. And my AFR is back to 11.7 :dunno:
And yes I ordered the Casper Unit. Hopefully that will make me safe enough to spray again.
And yes I ordered the Casper Unit. Hopefully that will make me safe enough to spray again.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
Well, I installed it today. Logged it with EFI. I saw no change in voltage @ WOT.
I did have to extend the wire that connected to the alternator positive terminal.
I did have to extend the wire that connected to the alternator positive terminal.
Last edited by Ed Blown Vert; Feb 24, 2006 at 11:25 PM.
Originally Posted by Ed Blown Vert
Well, I installed it today. Logged it with EFI. I saw no change in voltage @ WOT.
I did have to extend the wire that connected to the alternator positive terminal.
I did have to extend the wire that connected to the alternator positive terminal.
I was interested to see someone link to the Flowcharger. I have had one in the GTO, although it is currently simply serving as a relay. With a full 13.x volts from the alternator, the Walbro 255 l pump has not had trouble keeping up. But, it is ready to be boost activated as needed!
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
I will call them next week.
Originally Posted by 618HAWK
Did not want to hear that, hope I have better luck with mine. Are you going to give Caspers a call to see if they have any input?
Has anyone tried just using an electric tps senor connected to a relay t-ed into the stock wiring to the pump. You could adjust the tps switch to trigger at a set tps value. It would up the voltage to alternator voltage.
Thread Starter
Joined: Nov 2001
Posts: 3,066
Likes: 0
From: Sunny San Diego
Originally Posted by 618HAWK
Ed I take it you went with the Casper unit. post up on how the install goes along with the out come. Curious to see it preforms for you.
But not enough to get any more HP out.
So I will have to get a BAP. 20 amp or 40 amp?
BOSS APPROVED!
Originally Posted by Ed Blown Vert
It cleared up my lean out at 6300.
But not enough to get any more HP out.
So I will have to get a BAP. 20 amp or 40 amp?
But not enough to get any more HP out.
So I will have to get a BAP. 20 amp or 40 amp?
I spoke with Kenne Bell customer service last week and those muggles suggested the 40 amp version.
I'm having a MSD fuel pump booster and hot wire kit installed on monday. Exotic Performance has been installing the MSD unit. We'll see how it goes. Their dyno is down due to just moving so it might be a week until it gets tuned.
Originally Posted by WHPLASH
I'm having a MSD fuel pump booster and hot wire kit installed on monday. Exotic Performance has been installing the MSD unit. We'll see how it goes. Their dyno is down due to just moving so it might be a week until it gets tuned.
